4
4.0
Jan 7, 2021
01/21
by
Achim Ziermann (GuiliFPV)
data
eye 4
favorite 0
comment 0
Hello, this is my Naked Caddx Vista UFL Clamp. After removing the case, the ufl connector is not protected anymore. Weight is much less than 1 gramm. Printed in PETG with 20% infill Prints in less than 5 minutes. Edit: uploaded a new version. The first version was mirrored by accident.
Topics: naked, R/C Vehicles, iFlight, stl, vista, Chimera4, CADDX, Iflight_chimera4, thingiverse,...
4
4.0
Jan 5, 2021
01/21
by
Achim Ziermann (GuiliFPV)
data
eye 4
favorite 0
comment 0
Hi, I just received my brand new Betafpv 85x (DJI) drone. So I wanted to add some bright 2812 LEDs to the drone for Batterielevel and flash function. The adhesive Led strip just need something to hold it and I created a simple LES-Baseplate. I don`t have other 87mm drones or frames but I expect that most are very simliar, so you can use it on most drones of this type. Theoretically you can scale it down to use it on 75mm drones like the Mobula 7 too. Have fun adding LED`s Weight is ~ 1gramm. I...
Topics: betafpv, URUAV_UR85HD, R/C Vehicles, stl, Led_Holder, betafpv_85X, thingiverse, Uz85
4
4.0
Jan 4, 2021
01/21
by
Achim Ziermann (GuiliFPV)
data
eye 4
favorite 0
comment 0
Hi, this is my mount for the Beitian 220 GPS which is slightly larger than the Iflight original, however to big to fit. The 220GPS fits perfect. Printed in TPU 95a 65% infill.
Topics: Beitian_bn-220, R/C Vehicles, stl, iflight_xl5, thingiverse, gps_mount
3
3.0
Jan 4, 2021
01/21
by
Achim Ziermann (GuiliFPV)
data
eye 3
favorite 0
comment 0
Hi, this is simple Antenna cap. Any antenna tube with 3mm fits nicely, no wobbeling! If it is to long, just scale it down (or up) to have it optimal for you. Printed in TPU 95a.
Topics: Antenna_tube, R/C Vehicles, stl, FPV_Antenna_Caps, thingiverse
3
3.0
Jan 4, 2021
01/21
by
Achim Ziermann (GuiliFPV)
data
eye 3
favorite 0
comment 0
Hello, this is a Lipo 450mah battery clip for the Mobula6. Printed in PETG, 20% infill. PLA is not recommended, because it is not flexible enough and might break when mounting the battery with the clip. There is a cross which protects the lipo from hard landing and helps to have drone stays leveled during arming.
Topics: R/C Vehicles, stl, battery_holder, battery_clip, thingiverse, Mobula_6, Mobula6
3
3.0
Jan 5, 2021
01/21
by
Achim Ziermann (GuiliFPV)
data
eye 3
favorite 0
comment 0
Hi, this Idea is based on the Flight Controller Dirt Protection from the Diatone Roma. I really like this, because I using Props-Out configs and dirt/grass in the Flight Controller/USB ports is really nasty. This clip may fit to any frame where the standoffs are 5mm in diameter and where the mountingsholes have ~57,5mm distance. If it is close, it can be scaled down or up and should still fit. So this one is a clip on protector. Just print two, they fit each side. Probably I create one mor...
Topics: R/C Vehicles, iFlight, stl, iflight_xl5, iflight titan, flight_controller, thingiverse
4
4.0
Jan 6, 2021
01/21
by
Achim Ziermann (GuiliFPV)
data
eye 4
favorite 0
comment 0
Hello, this is my version of lightweight, stable Insta 360 One R FPV battery less case. You just need a +5v source for the cam from the battery or the Flighcontroller it the 5v BEC is strong enough. The case is below of 16gramm. Printed in PETG, 3 Walls and 40% (infill makes nearly no difference) The fit is tight and you have full access to USB/SD card and both buttons. Print the even long side as bottom with support.
Topics: R/C Vehicles, fpv_camera, stl, insta360, thingiverse, fpv, fpv_camera_mount, insta360_one_r
3
3.0
Jan 4, 2021
01/21
by
Achim Ziermann (GuiliFPV)
data
eye 3
favorite 0
comment 0
Hi, because the Draco-HD is very flat at the bottom, I want to protect the bottom against small stones and hard crashes/landing better. I created some cushion bumber which are mounted under the motor. I used 2 of screws with washer (you need longer 6-8mm longer screws for the Draco) So the motors are still hold by screws directly and 2 additional which also hold the bumbers. Motor is still stable. I used very soft TPU 50% so it has enough flexibility to soften a hard hit on the gound. TPU 95a...
Topics: R/C Vehicles, Motor-bumper, stl, Uvify Draco, thingiverse, Uvify
3
3.0
Jan 4, 2021
01/21
by
Achim Ziermann (GuiliFPV)
data
eye 3
favorite 0
comment 0
Hi, I use my Transtec Bettle Hom with a R-XSR receiver and didn`t found a good mounting option. So I created one, made of TPU 95A, 60% infill, very stable and flexible. Install it on the back, push the standoff thru the hole and install it. I had to resolder the Minus bat cable a little bit so there is 1mm more room, not a big issue. Insert the RX antenna in the holes at the bottom of the protector tubes and put a cable tie around the standoff, so everything stays in place. As a side effect the...
Topics: R/C Vehicles, Transtec, stl, antenna_mount, Antenna_holder, beetle, thingiverse
3
3.0
Jan 8, 2021
01/21
by
Achim Ziermann (GuiliFPV)
data
eye 3
favorite 0
comment 0
Hi, this my qTee Antenne for the Diatone Roma F5, may fit to similiar frames also. This keeps the antenna protected inside and vertical which provides better RF signal distribution compared to vertical mounting. This is printed in TPU with 90% infill. The Antenna near the frame on that image, is from behind. Fit the antenna tips first into the antenna mount and then put the white body in. Have fun and checkout my other Designs. Cheers. GuiliFpv
Topics: ghost, ImmersionRC, R/C Vehicles, diatone, stl, antenna_mount, ghost_qtee, qtee, thingiverse,...
3
3.0
Jan 6, 2021
01/21
by
Achim Ziermann (GuiliFPV)
data
eye 3
favorite 0
comment 0
Hi, recently I found this at Amazon (https://www.amazon.de/gp/product/B08DJ4P5JT/ref=ppx_yo_dt_b_asin_title_o04_s00?ie=UTF8&psc=1) A 350mAh 1s Lipo, ideal to squeeze even more flighttime out of the Mobula. The Lipo weights only 0,5gramm more than average 300mAh Lipos. Challenge was, to mount it properly, because of the lipo dimesion it is not holding inside the Mobula 6 Frame. So I converted my 450mAh clip somewhat, now the 350 1s lipo holds perfect into the frame. I will make a photo later...
Topics: R/C Vehicles, stl, battery_holder, mobula, thingiverse, Mobula_6, Mobula6
3
3.0
Jan 5, 2021
01/21
by
Achim Ziermann (GuiliFPV)
data
eye 3
favorite 0
comment 0
Hello, I created this very simple and scalable Lipo protector, to mainly reduce weight and I don`t need starting angle`s for racing. This Lipo Protector weight is about 6 gramm other that I found are nearly twice as this one. Print this in TPU95, Wall line count 2 with 80% Infill (more than enough). This one fits perfect for Tatu 850/750/650 3s/4s Lipos, however just scale it down to 20x70x10 or up to whatever you need. I will scale it down on my slicer for other Lipos I have to 20x80x10....
Topics: lipo_protection, R/C Vehicles, stl, lipo_case, LIPO_Holder, strap, thingiverse
3
3.0
Jan 4, 2021
01/21
by
Achim Ziermann (GuiliFPV)
data
eye 3
favorite 0
comment 0
Hello, recently my Bumblebee V2 crashed out of the air on concrete and broke the limited edition frame on the bottom and the top. May be these bumpers I created now, can dampen a hit enough to prevent it. Use it if you want some extra protection for the top and bottom frame. You will need ~2-3mm longer screws. Have fun. THESE Bumbers fit not the V1 frame. A image will be added shortly EDIT: The bottom Version is only slightly thicker then the Top version, by 0,5mm, if you want you can use top...
Topics: iflight_bumblebee, iflight_bumblebee_v2, R/C Vehicles, iFlight, stl, thingiverse
3
3.0
Jan 7, 2021
01/21
by
Achim Ziermann (GuiliFPV)
data
eye 3
favorite 0
comment 0
Hi, I created a combo mount for the ImmersionRC Ghost Cutie antenna and Iflight or Beitian 220 GPS. The Antennas can be mount vertically or horizontal. Personally I prefer vertically, because this physical the better antenna mount option compared to horizontal. Horizontal is mostly used because the size of the antenna don´t allow a vertical mount option, but with these antennas this is not neccessary. Because I don`t have TBS Tracer, I can`t create a special tracer version for it, otherwise I...
Topics: Beitian_bn-220, ghost, ImmersionRC, R/C Vehicles, stl, antenna_mount, ghost_qtee, iflight_xl5,...
4
4.0
Jan 7, 2021
01/21
by
Achim Ziermann (GuiliFPV)
data
eye 4
favorite 0
comment 0
Hello, this is a modified version of my Naked Caddx Vista UFL Clamp, but this Version has also a hole to use a tip tie, to protect the cable from ripping out of the ufl connector. After removing the case, the ufl connector is not protected anymore. Weight is much less than 1 gramm. Printed in PETG with 40% infill Prints in less than 10 minutes.
Topics: naked, R/C Vehicles, stl, dji_fpv, vista, CADDX, thingiverse, caddx_vista
3
3.0
Jun 12, 2021
06/21
by
Achim Ziermann (GuiliFPV)
data
eye 3
favorite 0
comment 0
Hi, this my qTee Antenne for the Diatone Roma F5, may fit to similiar frames also. This keeps the antenna protected inside and vertical which provides better RF signal distribution compared to vertical mounting. This is printed in TPU with 90% infill. The Antenna near the frame on that image, is from behind. Fit the antenna tips first into the antenna mount and then put the white body in. Have fun and checkout my other Designs. Cheers. GuiliFpv
Topics: Roma_F5, ImmersionRC, ghost, ghost_qtee, IRC, thingiverse, aircraft, antenna_mount, qtee, diatone,...
4
4.0
Jan 5, 2021
01/21
by
Achim Ziermann (GuiliFPV)
data
eye 4
favorite 0
comment 0
Hi, because I replaced the cheap FC from my Beetle Hom to a F7 Flight controller, I can now run bidirectional Dshot and LEDS at the same time. However there are also some Uarts free and I decided to add a GPS to the Beetle Hom. This is the completely fresh designed RX antenna with my Iflight Titan Beitian 220 GPS mount. With this you should be able to print this without support with TPU 95a. A picture follow as soon the print is finished and build into the Transtec Beetle. BTW: The RX Antenna...
Topics: R/C Vehicles, Transtec, stl, antenna_mount, Transtec Beetle, thingiverse, home, Hom, gps_mount
4
4.0
Jan 4, 2021
01/21
by
Achim Ziermann (GuiliFPV)
data
eye 4
favorite 0
comment 0
Hi, this is my clip to mount a 3S 300mah Lipo from side to side. Some Lipos are just a tiny bit to large to fit. The clip is printed in PETG weight is below 2 gram. Infill 25% 2 wall-lines With PEtg it is flexible enough, also I use a cross at thge bottom which help that the drone stays leveled and protects the Lipo on hard landings. The clip holds the Lipo tight to the drone. I made the same for the Mobula6 for 450mah lipos.
Topics: R/C Vehicles, stl, battery_holder, Mobula7, thingiverse, Mobula7_HD
3
3.0
Jan 4, 2021
01/21
by
Achim Ziermann (GuiliFPV)
data
eye 3
favorite 0
comment 0
Hello, this is my RX antenna mount for the Diatone R349 which comes on the hole an the end of the canopy. You need to drill a bigger hole do insert the antenna thru that hole into the Antenna Mount. It is a press fit, when done with TPU (95a). However I used uv-resin do secure it in place. I will add a photo later.
Topics: diatone_r349, R/C Vehicles, stl, antenna_mount, thingiverse
3
3.0
Jan 4, 2021
01/21
by
Achim Ziermann (GuiliFPV)
data
eye 3
favorite 0
comment 0
Hi, my prototype for a Mobula 7 VTX antenna Mount/Fin. Need to glues on the top, I recommend tpu 95A. My current used TPU is to soft and breaks, but with TPU95a it should have enough stability. Antenna angle to ~30-35degrees depending on exact mounting and canopy. I glued it with UV-resion onto the canopy and secured it additional with a zip tie on thru the canopy and over the front of the mount. Give it a try!
Topics: vtx_antenna_holder, R/C Vehicles, stl, Mobula7, thingiverse, Mobula7_HD
