3
3.0
Jun 20, 2021
06/21
by
Derrick Williams (Derrick_B)
data
eye 3
favorite 0
comment 0
This is a stand for all SCX24 trucks. Use the long rails to support the truck by the axles. This displays the truck as it would normally sit with the suspension compressed. Turn the base sideways and use the short rails to support the truck by the middle of the undercarriage. This is more of a storage configuration as it reduces stress on the suspension. Both methods are compatible with all stock wheelbases and extended wheelbases up to about 150mm (e.g. Micro Shark). The long rails have been...
Topics: R/C Vehicles, micro_crawler, thingiverse, stl, SCX24, Micro_Shark, rc_stand, radio_controlled
4
4.0
Jan 4, 2021
01/21
by
Derrick Williams (Derrick_B)
data
eye 4
favorite 0
comment 0
These are rear upper suspension links for the SCX24 Deadbolt designed to be used with high-clearance lower links. They are specific to the Deadbolt and will not work with the Jeep or C10. The purpose in making these was to solve a clearance issue. Typical rear lower high-clearance links hit the stock upper links when used with shock mount positions that allow for greater up travel. The middle bend in these links solves that issue. In that scenario, the stock upper links also hit the screw for...
Topics: R/C Vehicles, SCX24, stl, suspension, thingiverse
3
3.0
Jan 5, 2021
01/21
by
Derrick Williams (Derrick_B)
data
eye 3
favorite 0
comment 0
This is a simple tool to help with the installation and removal of SCX24 pivot balls found in the suspension links. It is designed to be used with a 4mm nut driver (the one you use with your wheel nuts). Installation 1. Insert the tool in the nut driver. 2. Place the pivot ball on the other end of the tool. 3. Place into the suspension link and press firmly. Removal is basically the same. BE ADVISED: If you apply too much force, you could break the tool and/or the pivot ball. The printed part...
Topics: R/C Vehicles, SCX24, stl, tool, thingiverse
3
3.0
Jun 19, 2021
06/21
by
Derrick Williams (Derrick_B)
data
eye 3
favorite 0
comment 0
I designed these handles for use with old home cabinetry, which sometimes uses handles with 3.25" spaced screws. Most modern cabinetry handles use 3" or 3.5" spaced handles. They attach with 10-24 bolts and nuts. Three versions of this design are included: shallow closed-top, deep closed-top, and shallow open-top. To install on one of these old cabinets: 1. Remove the old handle. 2. If it used a screw rather than a bolt (likely), drill a hole in the spot where the screws were...
Topics: Household, handle, thingiverse, drawer_handle, stl
3
3.0
Jan 4, 2021
01/21
by
Derrick Williams (Derrick_B)
data
eye 3
favorite 0
comment 0
I remixed Sundownnn's 4-link servo mount https://www.thingiverse.com/thing:4549464 after trying to use it with my Emax ES08MA II servo. There simply wasn't enough space. It is 0.9mm wider (0.8mm + 0.1mm for possible print inaccuracy). The Emax servo now fits without issue. I also extended the back of the mounting ears by 2mm to add back some strength and rounded the outside of the ears to help avoid snagging on the inside of the frame rails. I HIGHLY recommend clearing out all of the screw...
Topics: R/C Vehicles, SCX24, stl, thingiverse
3
3.0
Jan 4, 2021
01/21
by
Derrick Williams (Derrick_B)
data
eye 3
favorite 0
comment 0
These links will replace the stock lower links on the Axial SCX24 Deadbolt. They add clearance for easier crawling over rocks and other obstacles. Can be used with the stock pivot balls or in a custom install with 3.5mm ball studs.
Topics: SCX24, deadbolt, R/C Vehicles, stl, suspension, thingiverse
3
3.0
Jun 19, 2021
06/21
by
Derrick Williams (Derrick_B)
data
eye 3
favorite 0
comment 0
Easy to print, easy to use, extremely versatile, and completely reversable! This mount system allows you to attach phones, cameras, lights, microphones, and anything else that uses either a 1/4" camera mount or a cold shoe camera mount to your Flysky FS-GT5. Non-3D printed parts also needed: 3-1/2" 1/4-20 partially-threaded bolt 6" 1/4-20 partially-threaded bolt 8" Velcro strap with plastic buckle See a full walkthrough of the Bolt Edition mount system here:...
Topics: Radio_Control, RC_Car, R/C Vehicles, thingiverse, FlySky, stl, camera_mount
3
3.0
Jan 4, 2021
01/21
by
Derrick Williams (Derrick_B)
data
eye 3
favorite 0
comment 0
These beadlock wheels are designed to work with the 1.2" RC4WD Brick Edition tires. They will not work with 1.0" tires. The back of the wheels have a 7mm hex. They have been tested on my SCX24-based Micro Shark with mil stone wideners. The hub area is 2mm thick for extra strength, so the barrel nuts will barely grab. In my testing, it was enough. You can reduce the thickness if you have issues will the barrel nuts coming loose, but it will reduce the strength of the wheel. The wheels...
Topics: SCX24, R/C Vehicles, RC4WD, stl, beadlock, thingiverse
4
4.0
Jan 5, 2021
01/21
by
Derrick Williams (Derrick_B)
data
eye 4
favorite 0
comment 0
This is a stand for all SCX24 trucks. Use the long rails to support the truck by the axles. This displays the truck as it would normally sit with the suspension compressed. Turn the base sideways and use the short rails to support the truck by the middle of the undercarriage. This is more of a storage configuration as it reduces stress on the suspension. Both methods are compatible with all stock wheelbases, as well as extended wheelbases up to about 150mm (e.g. Micro Shark). The rails print as...
Topics: SCX24, R/C Vehicles, stl, thingiverse, rc_car_stand, RC_Car
