7
7.0
Mar 5, 2021
03/21
by
Matt L (Matt19888)
data
eye 7
favorite 0
comment 0
M12 x 1.75 threads The pic is black abs sanded smooth in steps starting with 320 grit and I worked my way to 1500 grit. I used a threaded piece and I stuck the other end in my drill. Will upload that tool shortly. You could make an easier job of this with slightly better results by sanding with just 320 grit and using an acetone vapor bath. I will likely try that with another knob. Link for tool:https://www.thingiverse.com/thing:3525268
Topics: Automotive, stl, shifter, ford mustang, Shift_knob, mustang, thingiverse
8
8.0
Mar 18, 2021
03/21
by
Matt L (Matt19888)
data
eye 8
favorite 0
comment 0
5mm wide opening. I will add some parts later for larger wrenches Assembly: Slide threaded part 3 thru part 2 and thread handle on which will hold everything together with the allen wrench inside Print handle at 101.5% for thread tolerance. Part 2 was given .6 tolerance in the design process but may need scaling depending on print settings. Handle has a 45 degree chamfer at the top on the inside so only a 10mm diameter circle will have to be bridged so this should print fine with no supports....
Topics: hex_wrench, t handle, stl, thingiverse, allen wrench, wrench, DIY
7
7.0
Apr 20, 2021
04/21
by
Matt L (Matt19888)
data
eye 7
favorite 0
comment 0
brace designed for the ap9's 36mm buffer tube. Wont fit anything else. #6 1 inch screws hold it in place. This is not a shoulder stock and was not designed to be used as one. Untested. Will update if there are any issues.
Topics: thingiverse, shuty_ap9, stl, DIY, pistol, shoulder brace, pistol brace
4
4.0
Mar 9, 2021
03/21
by
Matt L (Matt19888)
data
eye 4
favorite 0
comment 0
low profile attachment for getting under cabinets. 45mm total height.
Topics: stl, thingiverse, Vacuum_Adapter, shop vac, Replacement Parts, ShopVac, vacuum_cleaner
4
4.0
Apr 21, 2021
04/21
by
Matt L (Matt19888)
data
eye 4
favorite 0
comment 0
shopvac floor attachment v2. 45mm height for getting under cabinets,etc update:added supports to aid in high suction pulling pet hair off of couch.
Topics: thingiverse, stl, shopvac, Tools, shopvac_attachment, floor
4
4.0
Mar 9, 2021
03/21
by
Matt L (Matt19888)
data
eye 4
favorite 0
comment 0
made for pulling dirt,dust,and hair from fabric
Topics: stl, thingiverse, shopvac_attachment, Tools, shopvac
4
4.0
Mar 5, 2021
03/21
by
Matt L (Matt19888)
data
eye 4
favorite 0
comment 0
Clean version for polishing. No holes.
Topics: Automotive, stl, shifter, shifter knob, Shift_knob, mustang, thingiverse
5
5.0
Mar 4, 2021
03/21
by
Matt L (Matt19888)
data
eye 5
favorite 0
comment 0
Simple bracket for the sd card extension to go on the exterior of my heated enclosure.i use this extension....
Topics: sd card bracket, stl, sd_card, 3D Printer Accessories, SD_Card_Holder, thingiverse
3
3.0
May 1, 2021
05/21
by
Matt L (Matt19888)
data
eye 3
favorite 0
comment 0
I beefed it up a little. Thickened the walls to further prevent it from snapping off and I added some fillets to smooth out the baffles. Not sure if that will help with making the bb gun quieter but it should look nice. lol
Topics: stl, crossman_dpms, flash_suppressor, Sport & Outdoors, dpms, Suppressor, thingiverse
6
6.0
Mar 17, 2021
03/21
by
Matt L (Matt19888)
data
eye 6
favorite 0
comment 0
One of the nicest reprap cases on thingiverse in my opinion needed a mount as an option and I needed a mount for mine lol. You can also visit this link https://www.thingiverse.com/thing:3114849 and download the links to the articulating pi cam mount and they will work with this setup. same dimensions! Visit this link for the rest of the case parts. https://www.thingiverse.com/thing:2813298 Print as is with supports
Topics: reprap mount, 3D Printer Accessories, lcd mount, stl, reprap_discount, thingiverse, reprap smart,...
7
7.0
Jan 20, 2021
01/21
by
Matt L (Matt19888)
data
eye 7
favorite 0
comment 0
Latching spool organizer for priline style filament spools.2.2kg. line up the catches as seen in pic one and close the trays. upon closing it will latch. Printed mine in pla and it works great except that I had to file a bit of material pointed out in pic two. I removed some material in fusion after this so filing may not be required. I will update when I print these again or if someone beats me to it please msg me and let me know. tks
Topics: tray, spool tray, spool, thingiverse, spool organizer, Organization, priline, stl
7
7.0
Jan 20, 2021
01/21
by
Matt L (Matt19888)
data
eye 7
favorite 0
comment 0
detachable laser mount for x carriage found here. https://www.thingiverse.com/thing:2099577 Im sure it will work for a few others though. Also includes a slot for the driver to sit in. The mount itself is designed for a 30mm x 30mm laser. I purchased my 3.5w laser on ebay.
Topics: x carriage, 3D Printer Accessories, Anet_A8, laser mount, thingiverse, anet, stl, laser
6
6.0
Jan 21, 2021
01/21
by
Matt L (Matt19888)
data
eye 6
favorite 0
comment 0
Made this for my stepson who wanted it to store reloaded ammo 4in diameter by 6in height. I printed the lid at 101% and it threaded on perfect with no sanding filing,etc. Knowing your machine and tolerances is the key to getting a perfect print from this thing. Update 10/2: Thicker walls. Print without supports
Topics: NERF_AMMO, punisher, artifact_punisher, thingiverse, robot, Radio_Control, bottle, ammo,...
7
7.0
Mar 8, 2021
03/21
by
Matt L (Matt19888)
data
eye 7
favorite 0
comment 0
54mm diameter ball. A little larger than the stock knob and nicer for guys with large hands. Shift knob for manual 11 gt and threaded rod to stick in drill to sand and polish. This should fit all 10-14 mustangs.Maybe more? CHK your thread size first. thread size for this is M12 x 1.25 update: fixed a couple of fitment issues. It should be able to thread down passed where the threads end now and mate up with the leather boot a lot better. I took my measurements at night the first time and didnt...
Topics: Shift_knob, shifter, stl, thingiverse, Automotive, Mustang, Ford_Mustang
5
5.0
Mar 5, 2021
03/21
by
Matt L (Matt19888)
data
eye 5
favorite 0
comment 0
riser for condenser. Im sure this could have other uses.
Topics: condensor, DIY, stl, adjustable stand, heat pump, riser, thingiverse
6
6.0
Mar 5, 2021
03/21
by
Matt L (Matt19888)
data
eye 6
favorite 0
comment 0
Cold air intake for my 4.6 mustang gt. This should work on the older 5.0s as well, I’m not certain tho. The large elbow is meant to be plastic welded together with acetone. This is an abs part only. Pla will not work for this application. The 90mm pipe is meant to go into the fender well with the filter. The vacuum lines are meant to be acetone welded to the pipe as well. I will update later with the holes in the pipe in the correct positions but for now you can drill them out. 3.5mm thick...
Topics: Ford_Mustang, Automotive, stl, 90mm cai, cold air intake, mustang, air intake, thingiverse
8
8.0
Mar 5, 2021
03/21
by
Matt L (Matt19888)
data
eye 8
favorite 0
comment 0
Tool to install a shift knob on the end of a drill for faster sanding and polishing. Threads are M12 X 1.75. send me a message if you need a different thread size and I wil try to add it here.
Topics: Automotive, Sanding, stl, shifter, Shift_knob, gear_shifter, sanding_tool, thingiverse
7
7.0
Apr 18, 2021
04/21
by
Matt L (Matt19888)
data
eye 7
favorite 0
comment 0
New base for blade less fan found here. https://www.thingiverse.com/thing:2869887 Ive included two files. Both for 80mm fan of width up to 27mm. The original worked well for me but did need a little filing to get a nice snug fit. There were two very small ledges that showed up in my print so that could be the fault of my printer? So if your printer is finely tuned the original may work for you off the print bed. If not I added a millimeter of extra tolerance in the second file. revision 7/2/18:...
Topics: 80mm fan, desk fan, bladeless_fan, thingiverse, office, desk, stl, Office, summer
6
6.0
Jan 21, 2021
01/21
by
Matt L (Matt19888)
data
eye 6
favorite 0
comment 0
exterior vent for abs/laser. I didnt want to add a dryer style vent to a bedroom so heres my alternative. This should be fine for a standard 120mm fan but anything more than that might need more airflow. I plan on adding a grill for this later. Made in two pieces for easier printing.
Topics: enclosure vent, 3D Printer Accessories, thingiverse, abs vent, exterior vent, 4in vent, stl, laser
7
7.0
Apr 20, 2021
04/21
by
Matt L (Matt19888)
data
eye 7
favorite 0
comment 0
shopvac attachment for large shopvac hose. 38mm outer diameter. Print as is with no supports. update:10/1 made thicker and hose attachment end bigger for a more snug fit
Topics: Household, thingiverse, shopvac_adapter, stl, shopvac attachment, ShopVac
6
6.0
Mar 4, 2021
03/21
by
Matt L (Matt19888)
data
eye 6
favorite 0
comment 0
another sd card holder.
Topics: stl, computer, SD_Card_Holder, Electronics, case, sd card, thingiverse
6
6.0
Mar 3, 2021
03/21
by
Matt L (Matt19888)
data
eye 6
favorite 0
comment 0
tumbler lid with american flag. 82mm inner diameter and a 87.5mm outer diameter. designed to accept gasket from old lid.
Topics: tumbler lid, tumbler, Containers, coffee, thingiverse, stl, yeti
6
6.0
Mar 10, 2021
03/21
by
Matt L (Matt19888)
data
eye 6
favorite 0
comment 0
New edge Gt emblem! 1.5in tall approx. 3 3/4 wide. Same size as the stock fender and trunk emblems. If you print this for your car post a pic!
Topics: stl, thingiverse, mustang gt, Automotive, mustang, gt emblem, mustang emblem
6
6.0
Mar 22, 2021
03/21
by
Matt L (Matt19888)
data
eye 6
favorite 0
comment 0
parametric punisher skull with curved front. make as small as an inch wide or as big as you like
Topics: stl, the punisher, punisher, Props, punisher skull, thingiverse, skull
6
6.0
Mar 2, 2021
03/21
by
Matt L (Matt19888)
data
eye 6
favorite 0
comment 0
This was a nice design already. Very conservative. I only thickened the mounting plate by one mm and added some fillets and holes.
Topics: anet a8, y axis motor, thingiverse, stl, y axis brace, 3D Printer Accessories, y axis
7
7.0
Jan 21, 2021
01/21
by
Matt L (Matt19888)
data
eye 7
favorite 0
comment 0
Hvac vent for 1/2 bath. My half bath is about 20 sq ft so a 6x3 grill should be sufficient. Designed for use with a 4in duct. grill is meant to be press fit thru 1/2in drywall
Topics: hvac grill, hvac, hvac vent, vent grill, 6x3 vent, DIY, thingiverse, vent, 4in vent, stl
6
6.0
Mar 4, 2021
03/21
by
Matt L (Matt19888)
data
eye 6
favorite 0
comment 0
pi zero case. friction fit. no screws. if fit is loose or tight scale the lid. .3 tolerance on lid to base clearance. update:added a top with a tighter tolerance. worked well for me. it is .2 larger around the inside brim. it is labeled pizero7
Topics: stl, raspberry_pi_case, Raspberry_Pi, Electronics, Raspberry_Pi_Zero, thingiverse
4
4.0
Mar 5, 2021
03/21
by
Matt L (Matt19888)
data
eye 4
favorite 0
comment 0
This has completely eliminated any and all z wobble on my machine but in order to get this all working correctly it will take a bit of patience and effort beyond just printing everything and installing it. First a spring has to be installed from the harbor freight spring kit that is pictured but it will need to be trimmed down in small sections to get the correct lift off of the sliders. Too little and the carriage will bounce. Too much and there will be excessive friction and the sliders will...
Topics: stl, 3D Printer Accessories, prusa, Anet_A8, anti-wobble, anti z wobble, thingiverse
4
4.0
Mar 25, 2021
03/21
by
Matt L (Matt19888)
data
eye 4
favorite 0
comment 0
door handle for enclosure. Takes #8 screws. adjust the thickness of the plates to match your door thickness and screw length
Topics: stl, door handle, flsun cube, thingiverse, core xy, enclosure, handle, 3D Printer Accessories,...
3
3.0
Mar 25, 2021
03/21
by
Matt L (Matt19888)
data
eye 3
favorite 0
comment 0
extruder mount for 2020 extrusion t slot
Topics: stl, FLSUN_Cube, thingiverse, 2020 extrusion, hypercube_evolution, 2020, 3D Printer Parts,...
5
5.0
Mar 5, 2021
03/21
by
Matt L (Matt19888)
data
eye 5
favorite 0
comment 0
This is designed to be mounted behind sheetrock and the trim ring threaded in afterwards for a clean wiring install on a home subwoofer or this can also be used for surround sound speakers if using rca jacks as the connection point.The trim ring and retainer are there to allow soldering a female rca plug and mounting it into the bracket without twisting the wires when you thread the trim ring back into the sheetrock.
Topics: DIY, stl, surround_sound, rca, new construction, stereo wiring, thingiverse
5
5.0
Mar 9, 2021
03/21
by
Matt L (Matt19888)
data
eye 5
favorite 0
comment 0
converted to accept pennies instead metal cut out or eu coin.Also added some fillets for strength. update: moved penny slot up toward the rail and away from the actual gun slide. you will have to file down the penny on one side
Topics: stl, thingiverse, sight, sight press, Sport & Outdoors, glock
4
4.0
Mar 9, 2021
03/21
by
Matt L (Matt19888)
data
eye 4
favorite 0
comment 0
Just another shopvac tool.
Topics: stl, thingiverse, shopvac_attachment, crevice_tool, Tools, shopvac
16
16
Mar 9, 2021
03/21
by
Matt L (Matt19888)
data
eye 16
favorite 0
comment 0
Someone stealing your pens? Do you need a system that immediately emails you a pic of the perp in action? Look no further! A qi wireless charger fits into one side of the middle piece and a raspberry pi with the pi spy cam fits on the back side. Your phone covers the camera hole so you dont end up with only pictures of yourself and while you are gone the pi cam monitors your belongings. I used motion eye for the raspberry pi software. There are plenty of tutorials online from ppl who can...
Topics: Raspberry_Pi_Zero, stl, thingiverse, wireless_charger, Gadgets, raspberry_pi_camera, Raspberry_Pi,...
3
3.0
Jan 19, 2022
01/22
by
Matt L (Matt19888)
data
eye 3
favorite 0
comment 0
This thing has been optimized to print with abs and has slots for a zip tie if needed. I needed an extended shroud for this to fit with my sapphire pro e3d conversion
Topics: thingiverse, E3D V6 FAN SHROUD, E3D V6 40MM FAN, E3D_v6, stl, 3D Printer Parts
3
3.0
Jun 7, 2021
06/21
by
Matt L (Matt19888)
data
eye 3
favorite 0
comment 0
Mattress tool for dyson handheld. I used the connector from the remix link and added that to my own version of the mattress tool. update: added a few more fillets and center support for additional strength
Topics: dyson, thingiverse, stl, Dyson_vacuum, dyson_adapter, Vacuum_Adapter, Household
8
8.0
Jan 20, 2021
01/21
by
Matt L (Matt19888)
data
eye 8
favorite 0
comment 0
Pipe adapter. 4in to 6in.
Topics: DIY, stl, thingiverse
8
8.0
Jan 20, 2021
01/21
by
Matt L (Matt19888)
data
eye 8
favorite 0
comment 0
had to change this a couple of times to fix some measurement issues and it started to look like something so I went with it! Not a very good devil face but the measurements are spot on now.
Topics: 3D Printer Accessories, prusa_i3, anet a8, thingiverse, prusa, dial indicator, anet, stl
5
5.0
Jan 21, 2021
01/21
by
Matt L (Matt19888)
data
eye 5
favorite 0
comment 0
Running my mini shop vac without a filter and some of the little pieces like to come back out the exhaust side. This should minimize that to an extent. Im sure it will not work for fine dust but most other particles should get stuck in it.
Topics: sediment trap, diffuser, shop vac, thingiverse, Tools, stl
6
6.0
Jan 21, 2021
01/21
by
Matt L (Matt19888)
data
eye 6
favorite 0
comment 0
bl touch mount for x carriage found here. https://www.thingiverse.com/thing:2099577 I didnt need any shims with mine using a genuine e3d v6
Topics: e3d mount, 3D Printer Accessories, e3d, thingiverse, x carriage, bl touch mount, bl touch, stl
7
7.0
Jan 21, 2021
01/21
by
Matt L (Matt19888)
data
eye 7
favorite 0
comment 0
The bi rail stl in no longer needed for this part. I left it in on case someone wants it. .Consider this part for educational purposes only until you do your own testing. Could also possibly be used as a barrel cooler by stuffing a wet rag in the end to keep the pla from over heating! update: 9/3 added version 2 which includes longer body and 3 screw mount holes. 2 of which go into the upper which should help reinforce the barrel retainer. 9/7: added version 3 that eliminates the barrel...
Topics: quad rail, shuty ap9, thingiverse, gluty, Other, stl, ap9
4
4.0
Mar 9, 2021
03/21
by
Matt L (Matt19888)
data
eye 4
favorite 0
comment 0
Beefed up the sides a bit. My old one cracked after extended use. Also used a finer thread for more adjustment.
Topics: anet_a8_upgrade, stl, thingiverse, tensioner, x axis, Belt_Tensioner, Anet_A8, 3D Printer Parts
7
7.0
Jan 20, 2021
01/21
by
Matt L (Matt19888)
data
eye 7
favorite 0
comment 0
Just a simple handle latch combo.
Topics: 3D Printer Accessories, latch, thingiverse, door_handle, 3d_printer_enclosure, stl, Door_latch
6
6.0
Mar 8, 2021
03/21
by
Matt L (Matt19888)
data
eye 6
favorite 0
comment 0
strut cover for a 2011 mustang with 1960s style pony tri bar design. Had to omit a few features in the pony emblem to make this print well but it is not noticeable imo.You might have to use a tiny bit of silicone to get it to stay in place. update: thickened material behind emblem Contact me if you would like to purchase one of my other covers. I’m not releasing the stls at this time so please don’t ask. Thanks!
Topics: stl, thingiverse, strut, Automotive, mustang, strut cover, Ford_Mustang
4
4.0
Mar 8, 2021
03/21
by
Matt L (Matt19888)
data
eye 4
favorite 0
comment 0
echo case to hang on plug
Topics: Electronics, stl, thingiverse, echo dot, echo, Amazon_Echo_Dot
3
3.0
Mar 19, 2021
03/21
by
Matt L (Matt19888)
data
eye 3
favorite 0
comment 0
another simple enclosure latch. Parametric/scalable
Topics: sliding lock, lock, door lock, thingiverse, door latch, bolt latch, 3D Printer Parts, stl
3
3.0
Apr 4, 2021
04/21
by
Matt L (Matt19888)
data
eye 3
favorite 0
comment 0
Customized version of https://www.thingiverse.com/thing:2537701 Created with Customizer! https://www.thingiverse.com/apps/customizer/run?thing_id=2537701
Topics: thingiverse, 3D Printer Accessories, customized, stl
6
6.0
Mar 17, 2021
03/21
by
Matt L (Matt19888)
data
eye 6
favorite 0
comment 0
phobos remix without the flag
Topics: phobos, ar15, phobos remix, stl, ar15 lower, thingiverse, DIY, lower
7
7.0
Mar 17, 2021
03/21
by
Matt L (Matt19888)
data
eye 7
favorite 0
comment 0
2nd design of free float end cap. 45mm diameter 15mm center diameter
Topics: shuty_ap9, ar15, ar15_grip, ap9, free float, stl, thingiverse, end cap, DIY
3
3.0
Apr 4, 2021
04/21
by
Matt L (Matt19888)
data
eye 3
favorite 0
comment 0
sapphire pro drill guide for alignment of the pulleys and motors
Topics: thingiverse, corexy, 3D Printer Accessories, Sapphire_Pro, stl, Twotrees_Sapphire_Pro
