6
6.0
Jan 21, 2021
01/21
by
Tom Hobbs (Tom90)
data
eye 6
favorite 0
comment 0
A simple handle for an M5 thread tapper. Due the the torque produced while in use I would suggest 50% infill and 4x perimeter walls.
Topics: Thread Tapper, Thread tap, thingiverse, tapper, Thread, M5 Thread, Tools, tap, stl
6
6.0
Jan 21, 2021
01/21
by
Tom Hobbs (Tom90)
data
eye 6
favorite 0
comment 0
This is a mounting plate for the MKS Gen 1.4 board to fit inside the base of a kossel mini though should fit larger models. The spacing for the 2020 mounts is 60mm and is designed for M3 bolts and t-nuts. The board is held down by M4 bolts.
Topics: MKS GEN 1.4, 3D Printer Parts, MKS Gen, thingiverse, Kossel, 1.4, Delta, MKS, stl
7
7.0
Jan 21, 2021
01/21
by
Tom Hobbs (Tom90)
data
eye 7
favorite 0
comment 0
This is a coffee press for the Small Bialetti Moka express. The coffee holder has a diameter of 47mm so I designed the press with a 46.75mm diameter for a snug fit.
Topics: bialetti, Coffee, Mocha Express, Moka, thingiverse, Mocha, Moka Express, Press, Coffee Press,...
6
6.0
Jan 21, 2021
01/21
by
Tom Hobbs (Tom90)
data
eye 6
favorite 0
comment 0
This is a simple clip for the plastic storage boxes sold at Wilco in the UK. I am currently using one as a filament dry box. These clips are designed to be tight when 5mm foam strip is stuck around the inside of the lid and I use 10 to hold the box closed.
Topics: clip, wilco, stl, thingiverse, filament dry box, box clip, 3D Printing, dry box
6
6.0
Jan 21, 2021
01/21
by
Tom Hobbs (Tom90)
data
eye 6
favorite 0
comment 0
This is a mounting plate so a 60mm cooling fan can be fixed underneath the heat bed on a delta printer.
Topics: 3D Printer Parts, 60mm, Fan, Fan Mount, thingiverse, Kossel, Mount, Delta, stl
7
7.0
Jan 21, 2021
01/21
by
Tom Hobbs (Tom90)
data
eye 7
favorite 0
comment 0
As the CR10 has a fairly large footprint, I designed I designed some brackets to mount the control box to the side of an IKEA Lack table. They are designed for 4x M3 bolts to go all the way through the table from top to bottom and are held in place by M3 nuts on the other side.
Topics: Cr10, 3D Printer Parts, Bracket, IKEA, Lack, thingiverse, control box, cr-10, Mount, stl
9
9.0
Jan 21, 2021
01/21
by
Tom Hobbs (Tom90)
data
eye 9
favorite 0
comment 0
A simple bracket for mounting a Pi Cam to any tripod. You will need 4x M2 screws, standoffs and nuts to mount the camera module to the bracket and a 1/4 20 camera thread adaptor to glue into the mounting hole. This bracket is designed for the Pi Cam found here: https://www.ebay.co.uk/itm/Raspberry-Pi-Wide-Angle-Camera-Module-Pi-Zero-Cable-Included/153078067107?hash=item23a429efa3:g:aBwAAOSwi7RZKZt7
Topics: Camera, Raspberry_Pi, thingiverse, Raspberry, raspberry_pi_camera, Computer, stl
3
3.0
Sep 14, 2021
09/21
by
Tom Hobbs (Tom90)
data
eye 3
favorite 0
comment 0
Rubber hard drive mounts for the Fractal design HDD Tray kit – Type-B made by JensCraft20 found here: https://www.thingiverse.com/thing:4487637 Hard drives can be attached using standard 8mm M3 cap head bolts. Print in TPU 0.2mm Layer Height No supports required
Topics: stl, thingiverse, fractal_design, Computer, fractal_define
6
6.0
Jan 21, 2021
01/21
by
Tom Hobbs (Tom90)
data
eye 6
favorite 0
comment 0
Here is my case for a Raspberry Pi Zero W when being used as a dongle computer. I have also left an opening in the top so a heat sink can be added if needed. The holes are for M3 bolts and will cut their own thread into the bottom of the case. It is necessary to slightly widen the holes on the pi zero for this to fit as the stock holes are for M2.5. The small ridges in the middle of the bottom plate are for the hooks of a male USB plug to latch into before the unit is sandwiched together. When...
Topics: dongle, Raspberry_Pi_Zero, raspberry_pi_case, Raspberry_Pi_Zero_W, Raspberry_Pi, thingiverse,...
