4
4.0
Mar 16, 2021
03/21
by
Mike Collins (Abecia)
data
eye 4
favorite 0
comment 0
I didnt want the Berd-Air vibrating through my printer, so looked at ways to stop it. I fly RC Quads and thought about the mounts I use for the controller boards, Turns out they fit the job perfectly :) Just lay everything flat when you print them. Required 4x m3 flight controller dampers https://s.click.aliexpress.com/e/_A7nNUa 6x m3 nuts 4 x m3x8 2 x m3 x 10 Assembling 1. Fit 2 of the m3 nuts go in from the underside of the main body and the rear dampers screw into these 2. Mount the back...
Topics: berd_air, thingiverse, Berd-Air, HevORT, stl, 3D Printer Parts
6
6.0
Jun 20, 2021
06/21
by
Gary Collins (Gaza07)
data
eye 6
favorite 0
comment 0
This is my own design of a berd air bending and drilling jig, I have included several pictures to show how it is used, The holes in the tube are at 45 degrees the reason for this was because I found the normal straight drilled tubes didn't cool fine points to well and the nozzle heat would spoil the finish, The aluminium tube used was K & S 8101 Round Aluminium Tube (Pack of 3) 3/32" Dia x0.014" Wall and can be found here, I used a 1mm drill bit in a pin vice / chuck...
Topics: Berd Air Dill Jig, Berd Air Bender, thingiverse, 3D Printer Accessories, stl, Berd Air, smart...
2
2.0
Aug 22, 2021
08/21
by
Steffen Brck (TimesNewRoman)
data
eye 2
favorite 0
comment 0
Wanted an air pump holder that is easy to mount and has a fan mount. Print it in flexible filament to reduce noise.
Topics: 3D Printer Accessories, airpump, berd_air, Berd-Air, stl, thingiverse
5
5.0
Mar 25, 2021
03/21
by
Markus (toskium)
data
eye 5
favorite 0
comment 0
Berdair Anti Vibration Mount ====================== This mount is for the Berdair system. It is supposed to decouple the vibrating pump from the printer's frame. In addition I have added two large Noctua 80mm fans because the pump tends to run pretty hot. The mount is designed to be attached to a 3030 extrusion, it works vertically and horizontally, strong enough rubber bands provided. I am using 20mm diameter rubber bands, two rubber bands for each mount, this allows for horizontal and...
Topics: stl, Berdair, thingiverse, Berd-Air, Berd Air, 3D Printer Accessories
2
2.0
Oct 29, 2021
10/21
by
Lukas Donner (Lukas83)
data
eye 2
favorite 0
comment 0
I have made a Berd Air duct for the EVA print head. I tested it only with the Dragon hotend so far. There are little notches in the duct as a guide for the holes in the pipe. I closed the pipes by soldering them. You can use the drilling jig to cut the pipes to the correct length of 32mm. Just put the 3mm pipe into the hole, drill it with a 1,5mm drill and then cut it. I use the a 6/4mm tube to connect the Berd Air with the duct
Topics: thingiverse, vcore3, 3D Printer Parts, eva, stl, berd_air, Berd-Air
1
1.0
Apr 19, 2022
04/22
by
Henk Bezuidenhout (NeoAcheron)
data
eye 1
favorite 0
comment 0
Exactly the same mount as the source but it fits 3030 extrusion instead of 2020 extrusion.
Topics: 3030, 3D Printer Parts, thingiverse, berd_air, 3030_extrusion, stl, Berd-Air
9
9.0
Jan 11, 2021
01/21
by
Chris Androsoff (rocky00717)
data
eye 9
favorite 0
comment 0
Didn't like my air pump flopping around so designed this. Printed in flexible PLA with 15% infill.
Topics: berdair, thingiverse, stl, 3D Printer Parts, berd air, pump mount, berd-air
4
4.0
Mar 22, 2021
03/21
by
Thomas Quante (Woody1978)
data
eye 4
favorite 0
comment 0
Da ich kein flexibles material zum drucken da habe, hab ich die Form gemacht um es mit Silikon herzustellen. Since I have no flexible material to print, I made the mold to make it with silicone.
Topics: stl, berd_air, daypower, 3D Printer Accessories, Berd-Air, pollin, hypercube, thingiverse, hevo
4
4.0
May 1, 2021
05/21
by
Nick Schaf (NickSchaf)
data
eye 4
favorite 0
comment 0
Mount for the Berd Air tube that utilizes the mounting holes on the Duet Smart Effector. I didn't want anything hanging outside the extents of the Smart Effector, so this mount is held on to the Smart Effector via two of the mounting holes and holds the Berd Air tube through the third. Requires three M3x6 screws and one M3 nut. Obviously this design won't work if use something like a screw drive extruder, but works well with frame-mounted or flying extruders. Printed on my old i3v as I was...
Topics: stl, Berd-Air, berd_air, air_pump, 3D Printer Parts, Duet_Smart_Effector, thingiverse
2
2.0
Dec 13, 2021
12/21
by
Nicholas Musilu (mninja79)
data
eye 2
favorite 0
comment 0
This is a berd air pipe mount. Using two 2.5mm brass pipes with only on each. This is still a WIP
Topics: Berd-Air, stl, 3D Printing, thingiverse
4
4.0
Mar 21, 2021
03/21
by
Jeff Schaber (p40whk)
data
eye 4
favorite 0
comment 0
This is a remix of kuhnikuehnast's silencer case (without the silencer) to mount the Berd-Air pump horizontally from 3030 extrusion. I liked the way the pump mounted to the lid of this case but wanted a direct to frame mount that wasn't too big or bulky. You can print the frame mount in any hard material, I printed mine in PETG. Print all other parts in TPU.
Topics: stl, berd_air, 3030_mount, 3D Printer Accessories, mount, 3030, 3030_extrusion, Berd-Air,...
5
5.0
Mar 3, 2021
03/21
by
Morten Nielsen (dintid)
data
eye 5
favorite 0
comment 0
I created Berd Air Pipe Bend and Drill jigs in ordre to make my own Berd-Air Pipe which can't be bought here in Europe. It started out as simple remix but ended up as a total rework from ground up in order to make the inspirational source files into something to handle metric diameter tubing. I also found I'd like a different approach to drilling the holes - making it easier for me to just use a small electric drill, but included a second version in honor of my inspirational remix source ....
Topics: Bending tool, 3D Printer Parts, Tube bending, thingiverse, 3mm, stl, Berd-Air Jig, Berd-Air
6
6.0
Jun 20, 2021
06/21
by
Gary Collins (Gaza07)
data
eye 6
favorite 0
comment 0
Desk top stand for a berd air pump you can use silicone tube to trap the pump in the clamp or foam both work well, theres two versions of the clamp one with deeper grooves than the other, you will need a couple of 5mm screws and bolts to hold it together, I use this stand on both of my printers and they work very well, I sit the stand on a thin piece of foam to stop any vibes going through to the work surface / desk top
Topics: stl, thingiverse, berd air, 3D Printer Accessories
3
3.0
Mar 20, 2021
03/21
by
(guelz)
data
eye 3
favorite 0
comment 0
The name says it all! max overhang angle is 50° M3 Screw and Nut
Topics: thingiverse, 3D Printer Extruders, Berd-Air, stl
4
4.0
Mar 22, 2021
03/21
by
Joshua Vasquez (poofjunior)
data
eye 4
favorite 0
comment 0
Let's start with a [video breakdown](https://www.youtube.com/watch?v=rnl5iC12ndc). As we move into a world where toolchanging printers become the norm, we'll likely run into snags as the cost of the machine increases linearly with the number of tools. What if we could reimagine the problem tool costs as an opportunity to design shared infrastructure? The Berd-Air Selector is my first take on a compact, cheap solution for air cooling. This stepper-driven rotating selector allows us to reroute...
Topics: 3D Printer Accessories, thingiverse, stl, Berd-Air
3
3.0
May 1, 2021
05/21
by
Justin Witt (skbyfrk6)
data
eye 3
favorite 0
comment 0
While up grading to a Berd-Air system on my BLV cube I need a good mount to isolate vibrations from my frame. I found a Mount By ShadowX Thing #2849793. I liked the idea but was afraid that the rubber bands would break over time. My kid has Nerf rival balls scattered through out my house as I was picking them up and decided to try to use them as an vibration isolator. It work really well, no vibrations can be felt at all in my frame at any speed.
Topics: stl, thingiverse, Berd-Air, 3D Printer Parts
8
8.0
Apr 17, 2021
04/21
by
edwardo garabito (eddygara)
data
eye 8
favorite 0
comment 0
For anyone interested i just designed and made a clip that works very well for the Berd air max. Its a hassle free, not hardware required mode that, clips on too the 713 makers carbon standoffs. It can be adapted to work with other standoffs as well!
Topics: rostock_max, 3D Printer Parts, thingiverse, rostock_max_v2, stl, Berd-Air, rostock, 713_Maker,...
3
3.0
Jun 10, 2021
06/21
by
Ur Anium (Strontium90)
data
eye 3
favorite 0
comment 0
A mounting bracket to attach the Triangle Lab clone Chimera Aqua dual hot end with dual berd-air piping and an inductive probe to the Hypercube Evolution. A strain relief is provided for the watercooling pipes and plenty of anchoring points to keep the wiring tidy and out of the way. This version only has an optical end stop on the left for the "minimum" end stop. Brass threaded inserts are used to hold this sensor in place.
Topics: Chimera, berd_air, inductive_probe, thingiverse, hypercube, inductive_sensor, hypercube_evolution,...
2
2.0
Aug 22, 2021
08/21
by
Steffen Brck (TimesNewRoman)
data
eye 2
favorite 0
comment 0
Wanted an air pump holder that is easy to mount and has a fan mount. Print it in flexible filament to reduce noise.
Topics: airpump, air_pump, Berd-Air, stl, thingiverse, Electronics
6
6.0
Jun 10, 2021
06/21
by
Gary Collins (Gaza07)
data
eye 6
favorite 0
comment 0
Berd air tube support for the Duet smart effector, you can alter the height in your slicer if you require a longer version,
Topics: thingiverse, berd air, smart effector, 3D Printer Accessories, stl
10
10.0
Mar 12, 2021
03/21
by
Bob (bobunobu)
data
eye 10
favorite 0
comment 0
I needed a cover and mount for the eSwitch I purchased from the MakerHive, so I whipped something up quickly in OpenScad and it seems to work pretty well. http://www.themakerhive.com/shop/viewitem.php?productid=41
Topics: 3D Printer Accessories, thingiverse, MakerHive, Berd-Air, stl, eSwitch
3
3.0
Apr 4, 2021
04/21
by
James Ghawaly (TheStinkyRat)
data
eye 3
favorite 0
comment 0
This is a mount for connecting the Berd air cooling tube to the Railcore II MandalaRoseWorks dual/single y carriage. It is positioned to be able to swivel for use on both hotends, however it will work for a single extrusion setup as well. You will need some M3 bolts and nuts for this. I do NOT recommend printing this out of PLA. Hot air blows onto this mount from the hotend cooling fan, and it will melt if using PLA. PETG may work temporarily, but I wouldn't expect it to last long. I recommend...
Topics: thingiverse, 3D Printer Accessories, Railcore_300ZL, berd air, stl
3
3.0
Jun 21, 2021
06/21
by
Tyson Rudd (M3NT8L_One)
data
eye 3
favorite 0
comment 0
Here is V2 of my original Air Accumulator for Berd Air type cooling systems. This one is a bit more compact, but otherwise functions the same. Just fill it with something to dampen the air compression and pump piston noise. I show it dropping Decibels by 10 when in use Use one as an intake and one as an exhaust if needed.
Topics: Berd-Air, thingiverse, HevORT, stl, hevo, 3D Printing, cooling, air
8
8.0
Jan 17, 2021
01/21
by
Joe Mike Terranella (jterranella)
data
eye 8
favorite 0
comment 0
Simple mounting collar for an E3D hotend to a basic Delta effector. This extends out the side and allows the mounting of a Berd-Air Cooling tube for part cooling. There are slots to add nuts for the bolts to attach the opposite side. You'll need a couple of other parts to complete the mount: 2 - 3x14mm or 3x16mm bolts 2 - 3mm hex nuts or square nuts Berd-Air Cooling tube
Topics: E3D, 3D Printer Parts, delta, Berd-Air, thingiverse, kossel, stl
2
2.0
Oct 29, 2021
10/21
by
Ziggy Zig (Ziggy1)
data
eye 2
favorite 0
comment 0
Hemera Berd Mount with Side fangs and front pipe. It has some mesh issues and is a work in progress from a few other mods. You will need to adjust the opening in the front pipe so as not to take away to much pressure from the fangs. 1.02 Fangs are too close to block. Added New wide fang in 3 parts
Topics: thingiverse, hemera, stl, 3D Printer Accessories, Berd-Air, e3d_hemera
3
3.0
Aug 9, 2021
08/21
by
Michael Coar (guitartoys)
data
eye 3
favorite 0
comment 0
Hi, This is my take on a Berd Air tube mount for the HeVORT Hemera using the V6 hot end. I don't have access to an SLA printer to print the cool tube version. But this uses tubes, and just does a cut inside the block. I printed without supports, and then shoved a 16g wire in each of the holes to clear out any PetG hairs. Since I'm just now getting to the point of printing (hopefully this weekend), and want to use this hot end for a bit, and will then upgrade to Volcano Hot End. When I do, I...
Topics: Hemera, thingiverse, 3D Printer Parts, HeVORT, Berd Air, Berd, stl
3
3.0
May 1, 2021
05/21
by
Justin Witt (skbyfrk6)
data
eye 3
favorite 0
comment 0
This is a design based on the original STL by Ben. I order a metal kit for my BLV cube, and why I had it apart I decided to upgrade to optical sensors for the X and Y, and also install Bred-Air cooling pump. I used M3 and M2 heat set nuts for any threaded connections on parts. The Z off set for the BL-Touch is 0 X and Y- 55.4mm
Topics: stl, Berd-Air, 3D Printer Parts, BLV_mgn_cube, thingiverse
2
2.0
Dec 13, 2021
12/21
by
Yakov Gorodnitsky (kazolar)
data
eye 2
favorite 0
comment 0
This is a berd air mod for the Voron 2.4 or any printer than uses an AfterBurner print head. Print each part using standard voron settings .4mm nozzle/extrusion width, 4 perimeters, 5 top and bottom, 40% infill. The included parts are compatible with the mosquito and dragon hotends. You can re-use the back for the toolhead mount. You will need 3 barbed fittings -- 6mm OD 8-1mm thread. https://www.amazon.com/gp/product/B07Z9R3P9X/ref=ppx_yo_dt_b_search_asin_title?ie=UTF8&psc=1 Having an...
Topics: Berd-Air, voron_afterburner, stl, voron, thingiverse, 3D Printer Parts
10
10.0
Jan 18, 2021
01/21
by
Dech Amim (DechAmim)
data
eye 10
favorite 0
comment 0
Here's a simple OpenSCAD-based mount for the large motor used in the [Berd-Air MAX system](http://www.themakerhive.com/shop/viewitem.php?productid=45). As opposed to the mount published by MakerHive, which seems to be optimized for aluminum extrusion-based frames, this mount is intended for Prusa i3-style or boxy CoreXY printers with frames built out of flat materials. The motor is held in place with a strip of double-sided velcro (a few zip-ties are too puny to handle this gigantic motor),...
Topics: 3D Printer Accessories, Berd-Air, openscad, thingiverse, cooling, velcro, mount, stl
6
6.0
Mar 17, 2021
03/21
by
web web (warham)
data
eye 6
favorite 0
comment 0
https://www.youtube.com/watch?v=RbuojD_7rRg 2 parts, 1 for drilling and 1 for bending. The parts are labeled on the side what they are for. the top part is to screw onto the drill section. 1.20.19 open up the bottom to make drilling easier 2.22.19 trying figure out how to drill into bronze
Topics: hevo, berd air, 3D Printer Parts, stl, hypercube, thingiverse, hypercube_evolution
5
5.0
Mar 15, 2021
03/21
by
Tyson Rudd (M3NT8L_One)
data
eye 5
favorite 0
comment 0
Here is a carriage and front plate adapter for the HevORT 6mm HT or ST x/y assembly. This is designed for the Chimera using two V6 standard hot ends (The Volcano block is improperly shown for this version, as the BL touch mount is positioned for the standard V6) BL Touch Berd Air The rear has clamps for Berd Air style tubes to be held for wrapping around the bottom of the carriage for each of the hot ends The Front has a tube and wire clamp for securing the many water and PTFE tubes All .STL's...
Topics: 3D Printing, thingiverse, E3D, E3D_v6, Chimera, Berd-Air, HevORT, hevo, stl
6
6.0
Jan 21, 2021
01/21
by
William Tortorello (quadcells)
data
eye 6
favorite 0
comment 0
September 12th 2018 Update: I have included a mirror version of the Berd_Air_Floating_Base_v4.stl This is a remix of this model: https://www.thingiverse.com/thing:2875099 I was breaking elastic too often so I decide to make a mount using ant vibration balls from multi rotor cams. These are the balls I used: https://www.amazon.com/gp/product/B01F7T41GC/ref=oh_aui_detailpage_o04_s00?ie=UTF8&psc=1 40mm x 10mm fan 5v,12v or 24 depending on your needs. 4 M3 x 12mm pan head or cap screws for the...
Topics: 3D Printer Parts, 3d_printer, Berd-Air, 3D part cooling, thingiverse, stl
10
10.0
Jan 19, 2021
01/21
by
(kuhnikuehnast)
data
eye 10
favorite 0
comment 0
Tried to build my own "Berd-Air"-style tube. As there are no tube bender available on thingiverse that allowing to bend a 360°- circle, I had to design my own. The procedure of bending is quiet simple: 1.Things you need: - aluminium tube (3mm od) - screws: - 1 x M3 x 10 mm - 1 x M3 x 20 mm - 1 x M3 Nut (not necessary) - 2 x M6 screws (as lever) - drill (I took 1,5 mm) - plier - and a 3D-printer of course ;-) 2. Things to print: - 1 x U-form - 1 x Retainer - 2 x Wheel big - 1 x Wheel...
Topics: bending, 3D Printer Accessories, Berd-Air, thingiverse, bending_tool, bender, tube, stl
3
3.0
Mar 18, 2021
03/21
by
William Tortorello (quadcells)
data
eye 3
favorite 0
comment 0
I have found a brushless version of the motor/air pump assembly that I have been using for over 8 months. I run the motor at 30% most of the time and has worked out very well for my setup. Still more noise than using a fan, but I do not like having a fan mounted on my Smart Effector and taking up valuable real estate. I made two versions of the motor/air pump mount: ***1. Using Anti-Vibration Balls.*** ***2. Using a Float Style with Elastic Bands.*** I favor the Anti-Vibration balls version...
Topics: anti_vibration, part cooling, Berd-Air, thingiverse, layer cooling, 3D Printer Parts, stl
9
9.0
Jan 15, 2021
01/21
by
Tactical Pickle (Tactical_Pickle_Gaming)
data
eye 9
favorite 0
comment 0
This is just a simple mount i designed for the berd air max 3d printer layer cooling.
Topics: berdair, thingiverse, stl, Berd-Air, 3D Printer Accessories, mount, rostock max v2, bracket
1
1.0
Apr 20, 2022
04/22
by
Christopher Jorgensen (cjorgensenmd)
data
eye 1
favorite 0
comment 0
New x carriage for HevORT to be used with LGX lite and Mosquito hotend. Cooling accomplished with Berd air, but I would recommend not using the underside file because I am still working out kinks. designed for MGN12 Rails I used Craftcloud to get this SLS printed out of Nylon for durability and ease of manufacture.
Topics: 3D Printer Parts, sls, thingiverse, bondtech_lgx, Lgx lite, HevORT, stl, Berd-Air
9
9.0
Jan 12, 2021
01/21
by
Mekra (Mekra)
data
eye 9
favorite 0
comment 0
Pipe Holder that is designed to fix a 713 Effector and hold the pipes for a Berd-Air V2. Using 3mm Hex button Bolts to secure it down. I drilled out the hole for the effector mounting bolt. This piece does fit very snug on my effector. Note: My Extruder is not perfectly calibrated yet so parts may be slightly off if they are. let me know so I can adjust them.
Topics: berdair, thingiverse, 713_Maker, stl, 3D Printer Accessories, SeeMeCNC, 713maker, Rostock, Berd-Air
4
4.0
Jan 5, 2021
01/21
by
Nikolai Schauer (nikscha)
data
eye 4
favorite 0
comment 0
This solution allows for strong and lightweight cooling: Inspired by Berd-Air, fresh (cold) air is pumped to the "bracket" that mounts to the smart effector. There the air stream is split into two brass tubes which direct the air into the "nozzle". The minimal design reduces inertia of the print head and in case of a crash, only a single part (which doesn't require cooling to be printed) needs to be replaced. I use 2.5mm(od) brass tubing, cut down to a length of 46mm. A...
Topics: mosquito, stl, cooling_duct, smarteffector, tusk, Berd-Air, delta_effector, 3D Printer Parts,...
4
4.0
Jun 6, 2021
06/21
by
Simon Davie (NexxCat)
data
eye 4
favorite 0
comment 0
Update 20 Aug 2019: Added source Fusion 360 file A mount kit to fit a standard "Berd-Air" style air pump into the Anycubic Predator electronics enclosure. The mount is in two parts, the bracket to secure to the frame which can be printed in any material in my experience, and two dampener rings which sit between the motor and the brackets. I printed these in some cheap TPU with a 0.4mm nozzle. The end cap is provided to cover the exposed motor terminals and electronics, due to the heat...
Topics: predator, Anycubic, Berd-Air, thingiverse, Anycubic_Predator, 3D Printer Parts, stl, part_cooling
5
5.0
Mar 3, 2021
03/21
by
Terry Speake (Alexander_Mundy)
data
eye 5
favorite 0
comment 0
Edit: Uploaded a version with 80mm ball spacing & for 9mm belts for larger deltas. https://www.thingiverse.com/thing:3739808 Edit: Added Carriage belt wedge and Carriage tensioner STL's &.STEP files I forgot to include. Newer version of my Zesty Nimble effector and carriages for Trick Laser ball cup arms, E3D V6, and 20mm V slot. It has provisions for 2 air tubes for part cooling with an air pump. It is designed for maximum Z height and least nozzle tilt due to effector tilt and the...
Topics: delta_effector, 3D Printer Accessories, thingiverse, The_Zesty_Nimble, stl, Trick Laser, Berd-Air
4
4.0
Jul 25, 2021
07/21
by
Michael Coar (guitartoys)
data
eye 4
favorite 0
comment 0
This is just a little drilling jig I quickly knocked out to help drill straight tubes for the Berd Air mount for the HeVORT Hemera. Then a little slot to use a Dremel cut off wheel. Sorry no glamour shot of the part, already used it before I thought of taking a picture. I used a sheet of tablet paper folded over to help wedge the tube into the guide. Go slow, otherwise, you will find you rotate the tube a little with each drill. The holes are 5mm apart, and the second tube is offset by 2.5mm so...
Topics: HevORT, thingiverse, Drilling Jig, Hemera, Berd Air, stl, 3D Printer Parts, Berd, E3D Hemera
3
3.0
Oct 14, 2021
10/21
by
Francois C (tlex)
data
eye 3
favorite 0
comment 0
Printed in petg, No needs for nuts for the bltouch. Might need to redrill holes to allow gantry m3 bolts.
Topics: thingiverse, stl, 3D Printer Accessories, seckit_go_2, seckit_skgo, skgo2, Berd-Air, seckit
7
7.0
Apr 18, 2021
04/21
by
Dan Martin (danmartin6031)
data
eye 7
favorite 0
comment 0
A clip to hold the Berd-Air cooling pipe on evil_k's Titan Aero Mount. This clip hooks around the spacer on the back of the carriage for extra stability. I printed several iterations of this clip until I ended up with a tight fitment that wasn't too tight to assemble. You can scale the model up or down a few percent if you need to adjust the fit. I included the Fusion360 file if you would like to make larger modifications.
Topics: berd-air, thingiverse, cooling_fan, stl, e3d-titan, E3D_Titan_Aero, 3D Printer Extruders
4
4.0
May 1, 2021
05/21
by
Ignasi Trochut (Traca)
data
eye 4
favorite 0
comment 0
After purchasing a Orbiter 1.5 I wanted to fit my setup (ender 3 v1) with this extruder, but I couldn't find any design with this requirements: - Mosquito Hotend - Berd Air cool part - Inductive sensor - Endoscope I couldn't avoid to cut some parts to fit the bolts, if you have a better idea, just tell me :) I add the step file so if somebody can improve the design, just remix it.
Topics: stl, Berd-Air, inductive_sensor, Ender_3, 3D Printer Parts, Orbiter, mosquito, direct_drive,...
6
6.0
Jan 21, 2021
01/21
by
web web (warham)
data
eye 6
favorite 0
comment 0
I had this bracket laying around from my gimbal and thought it might work well for holding the berd air pump. I have not used the pump yet but i see many people making vibration dampening brackets that are way to complicated. So here is a simple one. add a couple 3mm screws and some rubber bands and your good to go
Topics: berd, berd mounting bracket, hypercube, 3D Printer Accessories, Berd-Air, thingiverse, hypercube...
4
4.0
Mar 15, 2021
03/21
by
Tyson Rudd (M3NT8L_One)
data
eye 4
favorite 0
comment 0
Here is the HevORT universal 6mm XCarriage for HT and ST x/y setups. This includes the BMG wind with volcano and bl touch. Also has Berd-Air paths built into the front plate. Use 4mm copper refrigeration tubing for making bent pipes to use as part cooling. Mellow BMG Wind 40mm fan for the front face E3D Volcano bl touch compressed air part cooling
Topics: 3D Printing, thingiverse, E3D, X_carriage, Berd-Air, BMG, HevORT, carriage, hevo, stl, volcano,...
2
2.0
Aug 8, 2021
08/21
by
Michael Coar (guitartoys)
data
eye 2
favorite 0
comment 0
Hi, This is my take on an anti-vibration mount for the Berd Air Pump. The main bracket can be PLA but I did it in PetG The little insert for the bottom I did in PetG, as I suspect it will get hot with the motor running. For the anti-vibration, I played around with 2,4 and 6mm thick Ninjaflex, and 4mm seems to be about right. I'm sure you could probably use just the top bracket, but as an overkill engineer, I used both. But if you only use a single top mount, you will probably be better off with...
Topics: thingiverse, anti-vibration, 3D Printer Parts, HevORT, BerdAir, Berd-Air, anti_vibration, Berd,...
4
4.0
Jul 3, 2021
07/21
by
Michael (AmmoMike83)
data
eye 4
favorite 0
comment 0
Berd Air DIN-Rail mount for Voron 2.4. Mounts to "pcb_din_clip_x3.stl" from Voron Design files.
Topics: rail, voron 2.4, DIN, 3D Printers, voron, Berd-Air, berd, berdair, air, thingiverse, stl, mount
10
10.0
Jan 18, 2021
01/21
by
William Tortorello (quadcells)
data
eye 10
favorite 0
comment 0
The Beard Air System Air Tube Holder is a remix of Zesty Tech's Berd Air tube holder (https://www.thingiverse.com/thing:2453322). I keep breaking the Zesty's air tube holder so I came up with this design after 16 different design changes. The vertical tube holder is a little thicker and I moved it to the back side of the Smart Effector. The Vertical tube holder is 8.5mm off center to line up with the hot end. There is a slot in the tube holder for a zip-tie to help secure the aluminum tube. The...
Topics: 3D Printer Parts, Berd-Air, thingiverse, Duet_Smart_Effector, delta_3D_printer, part_cooling, stl
8
8.0
Jan 19, 2021
01/21
by
William Tortorello (quadcells)
data
eye 8
favorite 0
comment 0
I was inspired by ShadowX's awesome motor mount design for the Berd Air System. https://www.thingiverse.com/thing:2849793 My needs were different so I did a little remix and came out with this. I didn't change ShadowX's 'Berd_Air_Floating_Base', but changed the Berd_Air_Baseplate to the Berd_Air_Pump_Fan_Baseplate and added the Berd_Air_Pump_Motor_Fan_Bracket. The 40mm Fan guard I am using is from Prot0typ1cal. You will need 5 or 6 silicone elastic bands or similar. 40mm x 10mm fan 5v,12v or 24...
Topics: 3D Printer Parts, 3d_printer, Berd-Air, thingiverse, 3D Part cooling, delta_3D_printer, stl
