9
9.0
Jan 11, 2021
01/21
by
Jacob Kongsø (SizZLeR)
data
eye 9
favorite 0
comment 0
This is a modded extruder bracket I made with a cable holder and expanded hole for filament input tube to be used for flex materials. In the process I added a cable holder on the side of it as the printbed on the CR-10 tends to rub against the cable when the printbed moves. In order to print flexible filaments with this, you take a piece of feeding tube (approx 10mm), stick it in the enlarged hole where the filament goes in, then cut the edge in an angle that best possible fits in between the...
Topics: Creality, thingiverse, Creality_CR-10, stl, 3D Printer Parts, creality_CR-10_s5, creality_CR-10_s4,...
7
7.0
Jan 14, 2021
01/21
by
Mr. DIY3DTech Dot Com (DIY3DTech)
data
eye 7
favorite 0
comment 0
So I was a having an issue with the Creality CR-10 pulling over the filament spool especially when it was full into the printer! Yes big ouch so I whiped these up and while one should work, two looks cool so up t you as should you print one and let it be lonely or two so it has company. Also worth note is the size of the of control box isn't perfect (are you surprised) so I made it for 125mm therefore you might find some extra rum between the uprights and the control box so use felt dots like...
Topics: Creality, thingiverse, Creality_CR-10, stl, 3D Printer Accessories, creality_CR-10_s5,...
8
8.0
Jan 14, 2021
01/21
by
Chris Garrett (makerhacks)
data
eye 8
favorite 0
comment 0
My X-Axis was thrown off level which made levelling the bed impossible, so I threw together these towers that fit over the bottom extrusion and allow you to lower the z to level the x-axis cross-beam. Note: Pull the plastic strips back on the bottom frame while levelling to ensure they don't throw off alignment
Topics: Creality_CR-10, thingiverse, stl, 3D Printer Accessories, creality_CR-10_s5, creality_CR-10_s4
11
11
Jan 12, 2021
01/21
by
Jacob Kongsø (SizZLeR)
data
eye 11
favorite 0
comment 0
Spool adaptor to fit the Creality spool arm to prevent the spool from tumbling and cause under-extrusion. I made this because when I adjusted my extruder steps per mm, I tested the impact of the counter drag from the spool which turned out to cause massive under extrusion. The impact was about 1-2mm of under extrusion, especially when the extruder pulls the filament enough to initiate a spool revolution but then retracts and refeed again, the spool would bounce, causing quite a pull and lead to...
Topics: Creality, thingiverse, Creality_CR-10, stl, 3D Printer Accessories, Afinibot_A31,...
6
6.0
Apr 17, 2021
04/21
by
mike de la vega (miketribal)
data
eye 6
favorite 0
comment 0
A little tool holder I use for my cr10's... Still a work in progress though lol, anyhow it will hole all the tools that came with the unit. so enjoy
Topics: creality_CR-10_s4, thingiverse, stl, creality_CR-10_s5, Creality_CR-10, CR10, Creality, 3D Printer...
6
6.0
Jan 16, 2021
01/21
by
Matt Allen (Mdog31000)
data
eye 6
favorite 0
comment 0
I am limited on space so i made this to help with that.
Topics: creality_CR-10_s5, 3D Printer Accessories, thingiverse, Creality_CR-10, stl
7
7.0
Jan 16, 2021
01/21
by
Mighty Jabba (MightyJabba)
data
eye 7
favorite 0
comment 0
I prefer to have my spool holder off to the left away from the printer's wires, but I found that when you put a full 1kg spool on it, the control box will have a tendency to tip over until some of the filament has been used. You can counteract that by placing something heavy (like another spool) on top of the box, but I decided to design this stabilizer to solve the problem. Just slide it onto the rear of the control box, avoiding the rubber feet and screws, etc. This fits my control box...
Topics: 3D Printer Accessories, thingiverse, creality_CR-10_s4, Creality_CR-10, stl
6
6.0
Jun 11, 2021
06/21
by
(Nicoaragon)
data
eye 6
favorite 0
comment 0
Summary Tapa superior ruedas, en la parte baja hay que colocarle una cinta de pelo que arrastrara el polvo del perfil guía de ruedas
Topics: thingiverse, Creality_CR-10, stl
6
6.0
Jun 20, 2021
06/21
by
Cesar Lopez (lowenski)
data
eye 6
favorite 0
comment 0
This is a replacement for the Creatily CR10 end/stop swtch board
Topics: Creality_CR-10, thingiverse, CR10, stl, 3D Printer Parts, creality_CR-10_s4
5
5.0
Jan 20, 2021
01/21
by
Mitch Davis (Thekakester)
data
eye 5
favorite 0
comment 0
If your filament is hitting the bed (or your part) and you need to raise it, this is a great print! No extra hardware needed. Mounts directly to extruder motor.
Topics: 3D Printer Parts, creality_CR-10_s5, filament, Creality_CR10s5, thingiverse, creality_CR-10_s4,...
8
8.0
Jan 16, 2021
01/21
by
Pierre-Henri Barbe (Petit_Homard_Breton)
data
eye 8
favorite 0
comment 0
Support for a Noctua NF-A6x25-FLX to replace one of the two fans in the bord. The other fan in the board can be replace directly by a Noctua NF-A4x20-FLX with out any support.
Topics: 3D Printer Parts, Creality, creality_CR-10_s5, cr10s, CR10S5, CR10S4, thingiverse,...
3
3.0
Mar 5, 2021
03/21
by
Anders Florinus (Florre)
data
eye 3
favorite 0
comment 0
This enclosure for the CR-10 Mini has all the parts you need except screws and plastic walls as well ass two or three LACK table from IKEA. It has also a little door at the side to make it easier to change filament. Total height inside is 53 cm or almost 21 inch (20,8).
Topics: stl, CR10, 3D Printer Accessories, Creality_CR-10, Creality_CR-10 mini, thingiverse
2
2.0
Mar 24, 2021
03/21
by
Angelo Spataro (AngeloS_1966)
data
eye 2
favorite 0
comment 0
There is no good baseplate for the dualgear extruder for the Creality CR10 (S). I made one including the filament sensor. The original lid of this filament sensor fits the one I designed. I have also added 2 wheels so that the filament goes straight into the extruder and does not sand anywhere and the filament sensor output is also directly opposite the extruder input. This is for wire feed from above, but also works with straight feed. The bearings that I used for the wheels are the same as in...
Topics: stl, Creality_CR-10_S, thingiverse, Creality_CR-10, Creality, 3D Printer Parts
6
6.0
Apr 17, 2021
04/21
by
Jason Baker (persuadu)
data
eye 6
favorite 0
comment 0
I took the dial gauge mount from cmdctrl and made a new mount for my CR-10. You cannot take the extruder all the way down when using this, but it does allow you to see how level your bed is and what areas need adjustment. I put a rubber band on the dial gauge just because it seemed a little loose. Please feel free to revise this and make a better version. JB UPDATE, the original fan mount blocked the fan completely. I have updated a vented version that will allow the fan to breathe while you...
Topics: creality_CR-10_s4, bed_leveling, thingiverse, stl, bed_level, creality_CR-10_s5, CR-10,...
7
7.0
Jan 13, 2021
01/21
by
wayne andrews (wayneuk)
data
eye 7
favorite 0
comment 0
finger tool
Topics: Creality_CR-10, thingiverse, stl, finger tool, 3D Printer Accessories, creality_CR-10_s5,...
5
5.0
Jan 21, 2021
01/21
by
pyriame caspase (Pyriame)
data
eye 5
favorite 0
comment 0
Remixed version of the chrisgeek level helpers for dual z CR-10 and CR-10 S4 or S5. improvements: -not touch the wire of the Z stopper (see picture) -does not touch the Z axis support (see picture) -allows use with frame hoses (see picture) -not necessary to remove them (see picture) Simply place on the bars sit each tower level with notch to the X. Ensure each block is sitting flat on frame railings. Enjoy.
Topics: creality_CR-10_s5, 3D Printer Accessories, thingiverse, creality_CR-10_s4, Creality_CR-10s,...
5
5.0
Jan 20, 2021
01/21
by
Jiri Stodulka (JiriStodulka)
data
eye 5
favorite 0
comment 0
Please make sure you have SCALE 101 or 102 % !!!! :P Model is OK but little tight and . need change rotation (info in photos) and print with supports For best detail Layer only 0,1
Topics: 3D Printer Parts, thingiverse, creality cr 10, labyrinth, Creality_CR-10, rotary dial, dial, stl
6
6.0
Jan 16, 2021
01/21
by
Peter Pham (thatguypeter)
data
eye 6
favorite 0
comment 0
I got my CR 10 a week ago and I couldn't find any insert that would fit the CR 10. The new spindle bar is smaller I think from previous model. I try some of the design on here and it didn't fit my CR 10 Spindle. I got try of wasting filaments so I designed this myself. The insert will fit most 2lbs and 1/2 lbs filament rolls. I have most of the PLA filaments from Amazon since we are doing some testing of them for a project. It's simple and work great!
Topics: creality_CR-10_s5, 3D Printer Accessories, thingiverse, creality_CR-10_s4, Creality_CR-10, cr_10,...
8
8.0
Jan 16, 2021
01/21
by
Mighty Jabba (MightyJabba)
data
eye 8
favorite 0
comment 0
The Creality CR-10S4 (which is the larger version of the CR-10 with a 400 x 400 x 400mm build volume) has a different construction than the normal CR-10, so the large wagon-wheel-style bed adjustment knobs that are so popular with CR-10 owners won't work. Since the standard knobs are pretty uncomfortable to use, I decided to design some more comfortable ones that will fit the S4. Just remove the knobs that came with the printer and press fit them firmly into these knobs. After designing these,...
Topics: Heated_Bed, 3D Printer Accessories, thingiverse, creality_CR-10_s4, Creality_CR-10, knob, stl
7
7.0
Jan 13, 2021
01/21
by
mike de la vega (miketribal)
data
eye 7
favorite 0
comment 0
I just added a couple supports for the upright section. Nice design, just noticed that it was bowing under the weight of some spools. So added the supports and so bowing
Topics: Creality, Creality_CR-10, thingiverse, stl, 3D Printer Accessories, creality_CR-10_s4, cr-10
5
5.0
Jun 11, 2021
06/21
by
(ART3FACTLab)
data
eye 5
favorite 0
comment 0
Summary One month using the alphawise U20... I love this machine, but after a month working with it, the filament sensor is broken !!!! so we decided to upgrade the system to make it work more efficiently ! Check it out !!!
Topics: thingiverse, alphawise, Creality_CR-10, stl
7
7.0
Jan 17, 2021
01/21
by
Shafiqur Khan (shfqrkhn)
data
eye 7
favorite 0
comment 0
Creality CR-10 MOAB (Mother of All Bombs) It's a great print to use up the whole volume (300x300x400mm) of the CR-10 and check for any ringing. Includes the GCode for the 300mm version. Can be scaled up for larger versions of the CR-10 as well. Note: You may need to put the model few mm below bed surface (within slicer) for it to print properly. Doesn't need any skirt, brim, etc. given the bed is level and everything is working properly. If S3D is giving you an error, do- "Edit>Scale to...
Topics: Creality_CR-10, stl, Sculptures, thingiverse
7
7.0
Apr 17, 2021
04/21
by
giorgio sali (pochetto)
data
eye 7
favorite 0
comment 0
https://www.paypal.com/pools/c/81EmSoZNia for donation https://youtu.be/LHWfNRmciHM https://youtu.be/QK8BMIYVKOo this is the quality I simply wanted to give a cue to be able to modify the cr 10 in something more precise and reliable .. and still a work in progress so follow .. you have the possibility to move the z axis in two ways, 1 with the classic screw system, 2 with the belt .. personally I prefer this last .. Thanks to blv for many stl..
Topics: 3D Printers, thingiverse, Creality_CR-10, stl
6
6.0
Jan 16, 2021
01/21
by
Joshua Westerfield (jdub1981)
data
eye 6
favorite 0
comment 0
Dimensionally accurate model created with Sketchup Make 2017. Purpose of the model is to create a good starting point for others to use in creating their own mods. Individual pieces may be printed from this model if needed. The model was entirely drawn in Sketchup 2017 and I have done my best to convert it to something more usable by the community. Sketchup files arent supported by Thingiverse so here is a direct link to the file on the Sketchup 3D Warehouse:...
Topics: 3D Printers, 3d_printer, thingiverse, creality_CR-10_s4, CR10, Creality_CR-10, CR10 Printer, stl
2
2.0
Mar 16, 2021
03/21
by
Robert Linder (ralinder)
data
eye 2
favorite 0
comment 0
Topics: stl, 3D Printers, thingiverse, Creality_CR-10
2
2.0
Mar 31, 2021
03/21
by
S Menke (Timetraveller)
data
eye 2
favorite 0
comment 0
For Spools with over sized holes
Topics: thingiverse, Creality, Creality_CR-10, Parts, stl
6
6.0
Jun 11, 2021
06/21
by
(Nicoaragon)
data
eye 6
favorite 0
comment 0
Summary Tapa limpiapolvo superior ruedas, la guía más expuesta a polvo. Colocar cinta de pelo en las extremidades inferiores.
Topics: CR10, Creality, thingiverse, Creality_CR-10, stl
6
6.0
Jan 17, 2021
01/21
by
chris Richardson (big_czar)
data
eye 6
favorite 0
comment 0
This is a replacement gear for a Black and Decker robot vacuum. The main brush motor has a small gear box with plastic gears. The front gear runs off the brass cog of the motor and is a soft plastic. This is the replacement for when it strips out. it printed in pla and abs, both where to soft. I ended up making it out of carbon fiber pla, it was strong enough to hold up.
Topics: Replacement Parts, Creality_CR-10, stl, thingiverse
8
8.0
Jan 17, 2021
01/21
by
Andres Serrano (Serranoware)
data
eye 8
favorite 0
comment 0
El legado dejado por Bruce Lee abarca desde películas hasta libros como El Tao Del Jeet Kune Do, donde se muestra gran parte de su filosofía y métodos de lucha. Su imagen perdura en el tiempo y ha quedado en la historia como una gran leyenda de las artes marciales, incluso, siendo elegido por la revista TIME como uno de los 100 hombres más influyentes del siglo XX, además de ser considerado como uno de los héroes e íconos de la historia.
Topics: Creality_CR-10, 3D Printing, stl, thingiverse
5
5.0
Jun 11, 2021
06/21
by
(benebrady)
data
eye 5
favorite 0
comment 0
Summary I've been using this filament sensor housing for the past few months and it's been very good. I needed to put a filament oiler on yesterday to support and all metal hot end and I didn't want one to be flopping around on the filament. So, I modified the filament sensor to allow the use of an oiler. Print Settings Printer Brand: Creality Printer: CR-10S Rafts: No Supports: Yes Resolution: 0.2 Infill: 35% Filament: Maker Geeks PLA
Topics: thingiverse, CR-10, Creality_CR-10, stl
5
5.0
Apr 18, 2021
04/21
by
Christoph Weinkum (raymax)
data
eye 5
favorite 0
comment 0
This is a nice LED Bar clip. NO SCREWS NO GLUE Just clip it in LED BAR: https://www.banggood.com/de/25CM-5W-Warm-White-Dimmable-25-SMD-5152-Super-Bright-Micro-USB-LED-Strip-Lights-p-972520.html?rmmds=search&cur_warehouse=CN And than a 2m micro USB cable If you want to support me: https://paypal.me/pools/c/84962v4zjk Please leave a comment and follow me on instagram: https://www.instagram.com/techgear3d/
Topics: creality_CR-10_s4, 3D Printer Parts, thingiverse, stl, Creality_CR-10s, Creality_CR-10, CR10,...
5
5.0
Jan 19, 2021
01/21
by
Roger Hayes (Skilled3DNovice)
data
eye 5
favorite 0
comment 0
This replaces the end cap on CR-10S and CR-10. I designed this to be able to add custom colored end caps to my CR-10S. This was also designed as proof of concept for a stable mounting point for a camera, sensors or other things that need mounting. I will upload variants of this with an arm to hold a camera or a light securely to the gantry.
Topics: Creality, creality_CR-10_s5, 3D Printer Accessories, thingiverse, 3D_Printer_Parts, Creality_CR-10,...
7
7.0
Jan 14, 2021
01/21
by
Nelio Oliveira (zombie_smix)
data
eye 7
favorite 0
comment 0
Support for inductive sensor to be used with autobed leveling. This is for a sensor of 18mm. Links for sensor: https://www.amazon.com/LJ18A3-8-Z-Approach-Sensor-Inductive-Proximity/dp/B008FZC8F2 https://pt.aliexpress.com/store/product/M18-8mm-sensing-DC-5V-NPN-NO-LJ18A3-8-Z-BX-5V-cylinder-inductive-proximity-sensor/1162433_32719316657.html
Topics: Creality, thingiverse, Creality_CR-10, stl, 3D Printer Accessories, inductive_sensor,...
7
7.0
Jan 17, 2021
01/21
by
medhat megahed (medmega)
data
eye 7
favorite 0
comment 0
infill 100 abs
Topics: Creality, creality_CR-10_s5, Created_with_FreeCAD, thingiverse, creality_CR-10_s4, Creality_CR-10s,...
8
8.0
Jan 18, 2021
01/21
by
wayne andrews (wayneuk)
data
eye 8
favorite 0
comment 0
required a mount to mount the fang on my microswiss 300 hotend also fits the stock hot end but did not want to keep removing the extruder bolts for the fang mount & come up with this .. internals need cutting out with side cutters . adjustable up & down some fangs are longer stock two screws to gantry to the left of the hot end 4 x m3 18 -20ish mm to secure the fan please note you made need to file a grove for the grub screw
Topics: creality_CR-10_s5, 3D Printer Accessories, cr1o, hictop, ender 2, thingiverse, creality_CR-10_s4,...
5
5.0
Jan 19, 2021
01/21
by
Paul de Graaff (pgraaff)
data
eye 5
favorite 0
comment 0
update 2018 05 08: added V2.1 with longer filament tube holder 08.05.2018 Version 2.1 mit längerem Filamentschlauchhalter hinzugefügt I gradet my Creality CR-10 to a CR-10S 300 up and used the opportunity to manage the cables new. I didn't like the movement of the filament tube and the cables of the hotend and so I designed attachments for the end stop holder and the hotend attachment. For the chain I used https://www.thingiverse.com/thing:2708420. You have to download and print the top and...
Topics: 3D Printer Parts, creality cr-10, Creality, creality_CR-10_s5, creality_ender_2, cable_management,...
6
6.0
Jan 17, 2021
01/21
by
Ham (HamDesigner)
data
eye 6
favorite 0
comment 0
Here's one of the handiest things I have created for the CR10 so far; a set of dovetail style quick-connect fixtures for the OEM hot end and the laser engraver. One can swap between printing and engraving/cutting in a matter of less than a minute. The reason I decided to go this route instead of mounting the laser with a magnet is that I wanted the least amount of offset from the normal tool center when going between printer and laser. To use, simply turn the cam lock lever to the left to...
Topics: creality_CR-10_s5, cr10s, CR10S5, 3D Printer Accessories, CR10S4, CR10_Printer, thingiverse,...
2
2.0
Mar 13, 2021
03/21
by
Morgan Lowe (morganlowe)
data
eye 2
favorite 0
comment 0
This is based on my other experiences in lead screw drives. This one is for the larger CR-10 S5 and S4 series machines. It uses easily available plus easy to print parts to achieve this. This is based off the [3DLS Complete Belt-Free 3D Printer](https://www.thingiverse.com/thing:4031698) #[First print](https://youtu.be/r2r6bCbSP3Y) I run SKR 1.4 on my machine and this is not possible with the stock control board. What you will gain is much improved Y axis performance at the cost of a little...
Topics: 3D Printer Parts, thingiverse, Creality_CR-10, lead_screw, Creality_CR-10s, leadscrew, stl,...
5
5.0
Jun 11, 2021
06/21
by
(benebrady)
data
eye 5
favorite 0
comment 0
Summary I've done a slight remix on my previous design that will allow you to print this shelf for the Raspberry Pi in a standard Pi enclosure and move it up off your desk. This shelf features a "Print and Click" v-slot rail so no hardware is required to put it onto your printer. Print Settings Printer Brand: Creality Printer: CR-10S Rafts: No Supports: Yes Resolution: 0.2 Infill: 15-20 % with triangles Filament: Solutech PLA Teal
Topics: thingiverse, creality_ender_3, Creality_CR-10, stl
6
6.0
Apr 17, 2021
04/21
by
Jay Carve (JeCarve)
data
eye 6
favorite 0
comment 0
This is a REMIX of Greg191134's Creality CR-10 Filament Guide https://www.thingiverse.com/thing:2186253 I replaced the filament guiding hook with a small housing for a filament filter. Fill this housing with i.e. a small piece of foam to keep the filament clean from dust and stuff. It might be more difficult to print than Greg's original filament guide and probably needs proper support. PLEASE SHARE AND COMMENT
Topics: 3D Printer Parts, thingiverse, Creality_CR-10, stl
6
6.0
Apr 17, 2021
04/21
by
mark szymura (blobby2012)
data
eye 6
favorite 0
comment 0
For dual axis, helps to keep track of any slippage of motors. mark coupler with pencil and every time you home, you can check they are both in synch. I have two marks, one is for painters tape and one for plain glass
Topics: thingiverse, Creality_CR-10, 3D Printer Accessories, stl
4
4.0
Mar 18, 2021
03/21
by
Jonathan Mercier (spool2kool)
data
eye 4
favorite 0
comment 0
This nut fits easier without the wheel bolt getting in the way.
Topics: 3D Printer Parts, stl, Creality_CR-10, thingiverse
3
3.0
Mar 22, 2021
03/21
by
Oliver Scheifinger (tokehs)
data
eye 3
favorite 0
comment 0
Anti Vibration Feet for the Creality CR-10's... Using 4 squash balls (2 yellow dot, available at amazon and others) and the original screws for fitting to the frame...
Topics: 3D Printer Accessories, thingiverse, stl, Creality_CR-10
6
6.0
Jan 17, 2021
01/21
by
giorgio sali (pochetto)
data
eye 6
favorite 0
comment 0
https://youtu.be/d7w5ZPzxHGc I released a new version for linear guide mgn 12 for x axis adapted to cr 10 .. I hope you like it
Topics: 3D Printer Accessories, Creality_CR-10, stl, thingiverse
6
6.0
Jan 17, 2021
01/21
by
gary OBRIEN (Gazz001)
data
eye 6
favorite 0
comment 0
guide wheel feeder for CR-10 with spool mounted on top. EDIT: added second base with cable holder
Topics: 3D Printer Accessories, Creality_CR-10, stl, thingiverse
6
6.0
Jan 15, 2021
01/21
by
Sven Seidler (bAD_kLOPFER)
data
eye 6
favorite 0
comment 0
As on Anet A8/A6 I dumped the springs under the heatbed and exchanged them with silicone dampers. These are the models of the mold. You need 5 M3-screws and nuts to assemble the mold parts. It would have been better to use 2 more screws but it works quite good as it is. You also need 4 M4-screws and nuts (I used the ones used for fixing the heatbed :-) ). Note: The heatbed-cables will be between damper and heatbed. If you are anxious you can cut the damper with a knife to provide a channel for...
Topics: Creality_CR-10, thingiverse, 3D Printer Parts, stl
2
2.0
May 1, 2021
05/21
by
Linus (LinuTec)
data
eye 2
favorite 0
comment 0
Folge mir für mehr: YouTube: https://www.youtube.com/channel/UCrfAj_MN0m9FmW9H1lb_47w Instagram: https://www.instagram.com/linutec/
Topics: stl, 3D Printers, Creality, Creality_CR-10, thingiverse
1
1.0
Nov 8, 2021
11/21
by
Kai Gutenschwager (spinne1984)
data
eye 1
favorite 0
comment 0
Der druck Dauert 58 Minuten ca
Topics: stl, Creality_CR-10, 3D Printer Parts, thingiverse
4
4.0
Mar 22, 2021
03/21
by
Oliver Scheifinger (tokehs)
data
eye 4
favorite 0
comment 0
In case you have an auto bed levelling (like BL Touch) in place the springs on the levelling screws can be replaced with this tubes in order to firmly attach the print bed to carriage since the springs and screws are no longer required to level the bed. This reduces wobble induced by the heavy bed moving on the y-axes sled and by that possible shadowing on the printed objects. Please note, that you should reduce acceleration to 500 - 800 and jerk to 5 - 8 in order to reduce stress and motion...
Topics: thingiverse, stl, Creality_CR-10, 3D Printer Parts
9
9.0
Jan 12, 2021
01/21
by
james steedman (0skillz)
data
eye 9
favorite 0
comment 0
Designed mount for the Logitech c270 webcam to attach to the CR 10 frame using one of the T nuts and allen screws that came with the printer.
Topics: 3D Printer Accessories, Creality_CR-10, thingiverse, stl
