10
10.0
Jan 18, 2021
01/21
by
Caleb Doe (cdoe)
data
eye 10
favorite 0
comment 0
This is version for smart effector and 40x40x10 fan. Needs 4 M2.5x20 screws. I've used brass tubes with 4mm OD from eBay and used drilling jig from https://www.thingiverse.com/thing:2445660 to drill holes.
Topics: 3D Printer Parts, openscad, thingiverse, Duet_Smart_Effector, stl
4
4.0
Mar 22, 2021
03/21
by
Niels Engeland (Rizza81)
data
eye 4
favorite 0
comment 0
I realized the the board from the smarteffector wobbles a litte bit. i want to try a reinforcement. THIS THING IS Work in process
Topics: stl, 3D Printer Parts, thingiverse, Duet_Smart_Effector, duet
4
4.0
Mar 15, 2021
03/21
by
Casey Adkins (ADKINCL)
data
eye 4
favorite 0
comment 0
I printed this on my TEVO Little Monster, which has a Duet 3 board, Duet smart effector, Haydn MagBalls and MagArms, and a E3D V6 hotend. The fan shroud is a modified SE300 fan shroud made to fit the Duet Smart Effector. Please not, this will cover the LED lights on the duet, but it should improve the part cooling issues that come with a duet smart effector. I have another version of the fan shroud that flips the orientation of the fan, so that it doesn't suck in hot air and/or stringy...
Topics: thingiverse, SeeMeCNC, Duet_Smart_Effector, Duet3D, stl, 3D Printer Parts
3
3.0
May 1, 2021
05/21
by
Henk Bezuidenhout (NeoAcheron)
data
eye 3
favorite 0
comment 0
Rail carriages to carry the Duet3D magnaball mount plates. The distance these protrude from the rails require no additional tweaking other than setting the new arm length in Marlin. The fit is tight, but not tight enough to struggle getting the bearings in and out. The strain relief is definitely needed for the cable, or you'll be replacing the connectors within a week. Make sure to use it with a pair of M3x8 screws and some cable ties.
Topics: stl, Duet3D, 3D Printer Parts, flsun, Duet_Smart_Effector, thingiverse
7
7.0
Jan 20, 2021
01/21
by
Felix Gerlach (GermanEngineer)
data
eye 7
favorite 0
comment 0
This hook is designed to hold the Smart Effector in a Think3DPrint3D Kossel XL Plus if it is too heavy to stay on its position after turning the printer off. Since this is the case after [mounting big fans to the Smart Effector](https://www.thingiverse.com/thing:2909853 "Smart Effector mounts for large fans"), I designed this hook. You need two M10 screws as counter weight in order for the hook to stay "open" by itself. When the Smart Effector is in home position you can...
Topics: t3dp3d, 3D Printer Accessories, thingiverse, Duet_Smart_Effector, think3dprint3d, stl
4
4.0
Mar 5, 2021
03/21
by
Niels Engeland (Rizza81)
data
eye 4
favorite 0
comment 0
This is my Smarteffecotr conversion for stock Predator Rods. You can use it upside down for more space. Print with your settings. i prefered Infill > 50%
Topics: Anycubic, stl, Duet_Smart_Effector, predator, Duet, 3D Printer Parts, thingiverse
8
8.0
Jun 20, 2021
06/21
by
Gary Collins (Gaza07)
data
eye 8
favorite 0
comment 0
Smart Effector 40mm Fan Adapter I used adapters that screw to the original E3d clip but wanted a single piece it fits with a nice click and holds firmly I fixed my fan to it using stainless steel self tapers and it doesnt affect the z probe at all Now updated to a v2 which has the corners inside removed and should cause less restriction
Topics: thingiverse, Duet_Smart_Effector, Smart_Effector_fan, stl, 3D Printer Parts
8
8.0
Jan 19, 2021
01/21
by
Felix Gerlach (GermanEngineer)
data
eye 8
favorite 0
comment 0
I wanted to have less noisy fans for my Kossel XL Plus which also provide a more powerful part cooling. Therefore I was thinking about a way to use a 40 mm fan for the cooling of my hotend and two 5015 radial blowers for part cooling. I did not want to reduce the printable area of the printer and therefore everything had to be tightly packed to the Smart Effector. I found JimboRRs nice design of a fan mount but did not want to remove the self tapping nuts at the Smart Effector when changing a...
Topics: 5015, 3D Printer Accessories, 40mm_fan, thingiverse, Duet_Smart_Effector, stl
10
10.0
Jan 17, 2021
01/21
by
Brandon (brandonh)
data
eye 10
favorite 0
comment 0
The [Duet Smart Effector](https://duet3d.com/wiki/Smart_effector_and_carriage_adapters_for_delta_printer) is a nice upgrade to a plastic effector. Nozzle-based probing, guaranteed-precise dimensions, built-in lights, and easy-to-detach cables. However, the provided 40mm fan shroud didn't seem to generate enough cooling with the 40mm fan I had, and axial fans aren't known to be great for part cooling anyway. I saw the [Tusk fan shroud...
Topics: DuetWifi, 3D Printer Parts, thingiverse, Kossel, Duet, Duet Smart Effector, Delta, stl
4
4.0
Jan 7, 2021
01/21
by
Peter Roß (P_C_R)
data
eye 4
favorite 0
comment 0
Adapter for mountinga Dragonfly on a Smart Effector. 4 Versions with .step included * Version with a M6 bowden coupling and 1.0mm M12 Pitch Thread * Version with a M6 bowden coupling and 1.5mm M12 Pitch Thread * Version with bowden collect and 1.0mm M12 Pitch Thread * Version with bowden collect and 1.5mm M12 Pitch Thread E3D Made two Versions of the V6 with M12 Thread. One with 1.0mm one with 1.5mm Pitch.
Topics: Phaetus, stl, E3D_v6, BMO, 3D Printer Parts, Duet_Smart_Effector, thingiverse
2
2.0
Jan 18, 2022
01/22
by
(LAD)
data
eye 2
favorite 0
comment 0
This is a mount that I created to install the Orbiter V2.0 direct drive extruder on my SeeMeCNC Rostock Max V2. I had been using the Orbiter V1.5 extruder and really like the control that came from having direct drive extruder, but the mount was not optimal due to the size of the extruder. The new size of the Orbiter V2.0 fixes the non-optimal mounting and creates a much nicer setup. I'm pleased that I can mount the Orbiter V2.0 directly above the E3D hotend and have a fully supported filament...
Topics: thingiverse, Duet_Smart_Effector, rostock_max, Orbiter_extruder, stl, 3D Printer Parts
3
3.0
Mar 17, 2021
03/21
by
Iurii Gavaga (shahfil)
data
eye 3
favorite 0
comment 0
Duet Smart Effector adapter for Dragon Hotend or mosquito clones. Just adapter or joined with fan shround.
Topics: Mosquito_hotend, 3D Printer Accessories, stl, thingiverse, Duet_Smart_Effector, Duet3D,...
3
3.0
Apr 8, 2021
04/21
by
Tom Simon (Jarvid)
data
eye 3
favorite 0
comment 0
Hi, this is a remix of jay_s_uk's (thanks for the duet conversion guide on your blog mate) nice Predator Smart Effector mount(https://www.thingiverse.com/thing:3603550) customized to fit v6 volcano hotends. The fan bracket is part of the ducts themself now as I was not satisfied with the stability of the original solution. So in summary you need to print less parts (not less material though) and you spare 2 screws for each fan. If you prefer the original assembly but fitted vor v6 volcano...
Topics: Anycubic_Predator, 3D Printer Parts, stl, 5015_fan_duct, thingiverse, Duet_Smart_Effector
2
2.0
Sep 13, 2021
09/21
by
Frederic Lecomte (Elescar)
data
eye 2
favorite 0
comment 0
Adapter to install a Dragon Hotend (Triangle Lab) on a Duet 3D Smart Effector. The PTFE tube is attached using a the Bowden Collet provided with the E3D heatsink (https://e3d-online.com/products/embedded-bowden-collet-for-metal-1-75mm?_pos=2&_sid=56a5618b9&_ss=r) __2021-09-06: __ - Added a version with 2 arms, it should prevent the Dragon to turn when changing the nozzle (not tested) - Add STEP file for the version with 2 arms __Print settings:__ - Adapter: PA-CF at .1 layer height -...
Topics: stl, Duet3D, thingiverse, 3D Printing, smart effector, Duet_Smart_Effector, delta_printer,...
8
8.0
Apr 17, 2021
04/21
by
Danny Lint (teamfox201)
data
eye 8
favorite 0
comment 0
Purchased the Duet Smart Effector for my custom built delta 3d printer and wanted to use my existing 35x35x10 mm blower fans on this effector. The fan bracket screwed to the bottom of the exposed thread from the magballs and fans screw into the bracket. Fans I am using: Delta Electronics BFB03505HA I have the Duet Smart Effector connected to the Azteeg X5 Mini v3, if you guys have any questions on the bracket or configuration of the Smart Effector with the Azteeg, feel free to post a question....
Topics: Smart_Effector_fan, 3D Printer Parts, thingiverse, Duet_Smart_Effector, stl, Smart_Effector_blower
3
3.0
Jul 22, 2021
07/21
by
Adam Shelburg (Asyborg)
data
eye 3
favorite 0
comment 0
I've been tweaking this for along time, just thought I would send it out and let others give it a try. It is designed for use with Maxiwatt hot end, Haden Magnetic Arms, 50mm fans Print Duct with ABS, the rest can be printed with PLA, the effector and carriages use 4 perimeters and high infill for stiffness. I have included the .step files, so remix to suit your needs.
Topics: Duet_Smart_Effector, smart effector, Predator effector, stl, 3D Printer Parts, thingiverse,...
4
4.0
Apr 4, 2021
04/21
by
Andreas Speicher (Tashen)
data
eye 4
favorite 0
comment 0
A simple remix which brings down the Fan ducts, so they can be used for the volcano hotend.
Topics: thingiverse, Duet_Smart_Effector, fan_duct, Anycubic_Predator, 3D Printer Parts, stl, Smart_effector
9
9.0
Apr 17, 2021
04/21
by
Christian Petry (christian_p)
data
eye 9
favorite 0
comment 0
This is a remix of dc42's design. My carriage hat too much flex so i designed it much stronger and with MUCH smaller tolerances. Additionally this takes the 2.1mm thick carriage adaptors into account which are added for the smart effector. Attach V-Rollers with one washer only, no need for a nut. I noticed the screws had play in their hole and would bend slightly because of the long lever due to the long distance to the rollers. So tighter tolerances and a single washer should improve this. I...
Topics: kossel, 3D Printer Parts, thingiverse, Smart_effector, v-rollers, Duet_Smart_Effector, stl, carriage
3
3.0
May 1, 2021
05/21
by
Nick Schaf (NickSchaf)
data
eye 3
favorite 0
comment 0
Mount for the Berd Air tube that utilizes the mounting holes on the Duet Smart Effector. I didn't want anything hanging outside the extents of the Smart Effector, so this mount is held on to the Smart Effector via two of the mounting holes and holds the Berd Air tube through the third. Requires three M3x6 screws and one M3 nut. Obviously this design won't work if use something like a screw drive extruder, but works well with frame-mounted or flying extruders. Printed on my old i3v as I was...
Topics: stl, Berd-Air, berd_air, air_pump, 3D Printer Parts, Duet_Smart_Effector, thingiverse
3
3.0
Jan 7, 2021
01/21
by
Peter Roß (P_C_R)
data
eye 3
favorite 0
comment 0
If you want to upgrade your Volcano Hotend to a BMO without changing fans etc. With the adapter the BMO will become the same lenght as a Threaded V6 with Volcano. You have 4 options * Adapter with M12 1.0 pitch and M6 Bowden Coupling * Adapter with M12 1.5 pitch and M6 Bowden Coupling * Adapter with M12 1.0 pitch and Insert Coupling * Adapter with M12 1.5 pitch and Insert Coupling + the Insert Adapter. This is for guiding the PTFE Tube The V6 Threaded Heatsink was sold with M12 1.0 pitch and...
Topics: Smart Effector, stl, BMO, 3D Printer Parts, duet, Duet_Smart_Effector, Volcano, thingiverse,...
9
9.0
Jan 16, 2021
01/21
by
Michael Peters (Mykal451)
data
eye 9
favorite 0
comment 0
Kossel / Delta Carriage designed for the Delta Smart Effector (from Duet3D) with the following machine parameters: IMPORTANT: Print this part on it's head as laid out in the STL file / view above, with supports. Or on the other end if your printer can handle up-sloping without supports. 1) 2040 vertical rails 2) 55mm Mag-Ball Diagonal Arm spacing (to match Delta Smart Effector) 3) Mini-VWheels 4) GT2 Belt 5) 10mm Magnetic Balls, with M3 x 10 stud 6) FYI My Delta is built with 16T Pulleys &...
Topics: 3D Printer Parts, delta_printer, 2040_extrusion, thingiverse, Duet_Smart_Effector, 2040_v_slot, stl
9
9.0
Jan 18, 2021
01/21
by
William Tortorello (quadcells)
data
eye 9
favorite 0
comment 0
The Beard Air System Air Tube Holder is a remix of Zesty Tech's Berd Air tube holder (https://www.thingiverse.com/thing:2453322). I keep breaking the Zesty's air tube holder so I came up with this design after 16 different design changes. The vertical tube holder is a little thicker and I moved it to the back side of the Smart Effector. The Vertical tube holder is 8.5mm off center to line up with the hot end. There is a slot in the tube holder for a zip-tie to help secure the aluminum tube. The...
Topics: 3D Printer Parts, Berd-Air, thingiverse, Duet_Smart_Effector, delta_3D_printer, part_cooling, stl
8
8.0
Mar 3, 2021
03/21
by
Christian Petry (christian_p)
data
eye 8
favorite 0
comment 0
This is a model of the Duet Smart Effector. It includes most of the connectors and LEDs so it can be used to design a cooling solution or other attachments where you have to take care of the very limited space. Note the E3DV6 has a grove mount which is NOT what you will use on the smart effector, there is a special version using a thread/nut combination. I reused the E3DV6 model from somewhere and would like to attribute by providing a link, but cannot find it :-(
Topics: Duet_Smart_Effector, delta_effector, delta_printer, Duet3D, 3D Printer Parts, Duet, thingiverse,...
10
10.0
Apr 17, 2021
04/21
by
Richard Norman (RGN01)
data
eye 10
favorite 0
comment 0
Update 2018/02/10: Added two more duct sections - one for 5mm OD aluminium tubes and one for 6mm OD tubes This set of parts is designed to fit the DC42 Smart Effector. It uses a 40x15 blower fan and uses the 'tusk' approach. There are 4 components to this set: - the duct that the tusks fit into. Two versions are supplied - one has a ridge to aid seating into the collar. I use the version without this collar but you may choose to use the version with the rim - a collar that is glued to the fan...
Topics: Smart_Effector_fan, 3D Printer Parts, Smart_effector, thingiverse, Duet_Smart_Effector, stl,...
4
4.0
Jun 10, 2021
06/21
by
Niels Engeland (Rizza81)
data
eye 4
favorite 0
comment 0
Edit: 2019-08-15: i forgot to upload the V2 PCB Adapter with the cutout for the carriage screws. Here they are. Edit: 2019-07-22: Added two Version for the original Smarteffector PCB Board. One with Flying extruder and one without flying extruder holes. This is my carriage adapter for Hayden Huntleys magball Rod. Printer: Anycubic Predator
Topics: Hayden_Huntley, Anycubic, magball, balljoint, 3D Printer Parts, thingiverse, Duet_Smart_Effector,...
3
3.0
Oct 15, 2021
10/21
by
Frederic Lecomte (Elescar)
data
eye 3
favorite 0
comment 0
MGN12 adapter for the Anycubic Predator, rails are mounted directly on the extrusion without any adapters. I have been printing with these carriage for a few weeks already at 150mm/s outside wall; 200mm/s inside wall and infill with no issues. Requires: - 6x 12mm M3 - 12x 16mm M3 - 3x 6mm M4 - They are used to attach the springs for the flying extruder, stock screws can be reused - 12x Zip Ties for the belts (recommended) Th zip tie attach must be facing the linear rails, if the the opposite...
Topics: 3D Printers, thingiverse, stl, Duet_Smart_Effector, delta_printer, due3d_smart_effector,...
3
3.0
Mar 18, 2021
03/21
by
Jay (jay_s_uk)
data
eye 3
favorite 0
comment 0
This is taken from my setup for the predator. I have since changed my rods to magball ones (thanks Haydn!) and no longer needed to use my converter design with the smart effector. This resulted in my fans being too high, so I have modified the fan ducts and the fan brackets. This will fit all smart effectors when used with magball arms. You need to print one of each duct and 3 brackets. They mount on the threads of the magballs. I have printed them in PLA. The heat does affect them slightly but...
Topics: part, button, Duet_Smart_Effector, thingiverse, replace, Smart_effector, Smart_Effector_fan, 3D...
7
7.0
Jan 19, 2021
01/21
by
Richard Norman (RGN01)
data
eye 7
favorite 0
comment 0
I wanted to fit a Noctua 40mm fan to my Smart Effectors (one with an e3V6 and one with a Volcano) so came up with this. One of my design objectives was to mechanically isolate the fan duct from the heatsink and the Z-probe capability so this mount fits onto the ball studs and only touches the PCB at these points. There are four versions: - one for no accessories (both ball stud mounts are the same height) - one that allows various accessories to be added (through having one 'foot' thinner than...
Topics: 3D Printer Parts, Smart_effector, Noctua_Fan_40mm, thingiverse, Duet, Duet_Smart_Effector, stl,...
3
3.0
Mar 16, 2021
03/21
by
Miklós Galicz (gnick666)
data
eye 3
favorite 0
comment 0
This is a solution to mount the SmartEffector's mounting plate to the QQ-S' sliders, and yes, by printing your own sliders. **Word of Caution**: You might want to get another batch of bearings/bushings as the original ones can be hard to extract without damaging the original carriage. _If you damage your original carriages, remember: I didn't tell you make this upgrade, and you're doing it at your own risk._
Topics: Flsun_qq-s, thingiverse, flsun_qq_s, flsun_qqs, Duet_Smart_Effector, smarteffector, stl, 3D Printer...
3
3.0
Mar 31, 2021
03/21
by
Red (Redemptioner)
data
eye 3
favorite 0
comment 0
A bunch of people have been bugging me to put up my fan duct design for the Duet smart Effector. I am reluctant to release this model as there are many things that are simply done wrong on the smart effector that I am not a fan of promoting it. The obsession with screw connectors for heaters and the ridiculous variance in connectors on the effector (for god sake they have 2 different connectors for the 2 fan outputs, both of which are not a standard fan connector and 5 times the size the need...
Topics: Duet, Duet2Ethernet, Smart Effector, Tevo Little Monster, thingiverse, 3D Printer Parts, Duet Smart...
4
4.0
May 1, 2021
05/21
by
Nathan Conover (NDCSR)
data
eye 4
favorite 0
comment 0
Remixed to clear my arms at full extreme range of motion. Adjusted to position airflow on nozzle again. The nozzle needs support in this version and must be printed at the best resolution you can achieve. Position with the inlet up.
Topics: stl, smart effector, thingiverse, duet, duet smart effector, fan, cooling, 3D Printer Accessories,...
2
2.0
Dec 14, 2021
12/21
by
Henrik Andersson (Snimax)
data
eye 2
favorite 0
comment 0
Adapter to mount an orbiter 2.0 extruder to a smart effector board. Its probably easiest to print with the orbiter side rotated towards the build plate and with supports for the smart effector mount holes. This is a work in progress and I haven't received an extruder to try it with yet, thus I cannot be sure it wont hit the rods while printing.
Topics: Smart_effector, 3D Printer Extruders, Orbiter_extruder, stl, thingiverse, Orbiter,...
9
9.0
Jan 18, 2021
01/21
by
Danal Estes (Danal)
data
eye 9
favorite 0
comment 0
Many carriages for Linear Sliders on TV already. However, I could not find one for 9mm belts. This has 55mm ball spacing, intended for a Duet Smart Effector. It is OpenSCAD, so that can be changed fairly easily. Also, the spacing of the carriage holes can easily be changed for other linear sliders. It also features a belt tightener. . By the way, 9mm belts are almost twice as "non-stretchy" as 6mm belts. You do have to change pulleys, idlers, etc. This can be very easy, or very hard,...
Topics: 3D Printer Parts, Carriage, tightener, thingiverse, Duet_Smart_Effector, Linear_Slide, belt,...
2
2.0
Sep 13, 2021
09/21
by
Frederic Lecomte (Elescar)
data
eye 2
favorite 0
comment 0
Adapter to install a LIS3DH Triple-Axis Accelerometer on a Duet3D Smart Effector. __Part required:__ - 4 M2.5 x 6mm screws - LIS3DH Triple-Axis Accelerometer (https://bc-robotics.com/shop/adafruit-lis3dh-triple-axis-accelerometer/) - 1 M3 x 6mm screw - 1 M3 nut - ideal a locknut __Print settings:__ - ABS+ at .2mm layer height
Topics: stl, due3d_smart_effector, Duet, thingiverse, Duet3D, 3D Printing, Duet_Smart_Effector,...
10
10.0
Jan 18, 2021
01/21
by
William Tortorello (quadcells)
data
eye 10
favorite 0
comment 0
This is a remix of my Delta Carriage for 2020 Aluminum V-Slot® 20x20 Linear Rail: https://www.thingiverse.com/thing:2753542. This is exactly the same except that the Mag Ball spacing is 55mm instead of 48mm spacing. So please head over to the original design for instructions and parts list. I made this one to go with the Duet PCB Smart Effector. **July 18th 2018 Update:** Cleaned up the carriage a bit and removed some holes that I thought were not needed. Since I made to be mounted to the...
Topics: 3D Printers, Duet3D, thingiverse, 2020_extrusion, V-Slot, Duet, Duet_Smart_Effector,...
5
5.0
Mar 17, 2021
03/21
by
Jon Dunfee (bLITzJoN)
data
eye 5
favorite 0
comment 0
I finally got tired BL-Touch pin drops, inconsistencies and finally the bent pin! I decided to research into piezo bed leveling. I picked up an [Orion Precision Piezo PCB](https://www.precisionpiezo.co.uk/product-page/precision-piezo-orion-pcb). The journey didn't go quite a smoothly as I was hoping; mostly self-inflicted design flaws of my custom brackets since I wanted to utilize as much of the stock components as possible (e.g. fans, effector, etc...). I also didn't want to use a PTC...
Topics: precision_piezo, tevo_delta, tevo, TLM, 3D Printer Parts, piezo, stl, tevo_little_monster, Duet,...
3
3.0
Jan 19, 2022
01/22
by
Frederic Lecomte (Elescar)
data
eye 3
favorite 0
comment 0
10mm socket for magballs (Haydn). Using a printed socket instead of a metal socket prevent to damage the traces on the Duet Smart Effector. Should be ideally printed on ABS or PETG; PLA is fine
Topics: delta_printer, thingiverse, Duet_Smart_Effector, delta_effector, FLSUN_Delta, Anycubic_Predator, 3D...
4
4.0
Jun 11, 2021
06/21
by
(ZestyTech)
data
eye 4
favorite 0
comment 0
Summary This adapter is specifically to mount the Nimble Version 2 on the PCB effector that Escher3D is developing with Think3dPrint3d. It uses a new hot end mount that is developed by E3D. Have a look at the Duet effector [here.] (https://duet3d.com/wiki/Smart_effector_and_carriage_adapters_for_delta_printer) Simply bolt the adapter to the hot end mount and bolt the Nimble V2 to the adapter. Changelog: 1 Initial release. The STL models are checked and optimised. The parts that need a different...
Topics: Nimble_Extruder, Adapter, thingiverse, Duet_Smart_Effector, Nimble V2, Extruder, Smart_effector,...
2
2.0
Sep 13, 2021
09/21
by
Frederic Lecomte (Elescar)
data
eye 2
favorite 0
comment 0
Smart Effector adapter to attach the tubes from a Berd Air Pump. __Required parts:__ - 3x M2.5 screws, there is 2 holes but only 1 is required, use the 2nd is the thread on the first one is failing - only needs little pressure on the pipes - Pipe (brass) outer diameter: 2.5mm - Plastic tube inner diameter:5mm __Print settings:__ - ABS+ at .2 layer height
Topics: stl, Duet, Duet3D, thingiverse, 3D Printing, delta_3D_printer, airpump, air_pump, delta_printer,...
3
3.0
Jan 7, 2021
01/21
by
Robert Lorincz (lorinczroby)
data
eye 3
favorite 0
comment 0
Orbiter adapter for Duet Delta effector based delta printers. The adapter is mounted to the efector using: - 3x 6-10mm M2.5 + 3x M2.5 insert nuts in the adapter (you can use M3 screws and nuts as well but you will need to enlarge the holes in the effector PCB to 3.2mm); - 2x 10mm M3 nuts + 2x M3 insert nuts in the adapter for mounting the orbiter on top. Thanks Frank G. for helping and supporting this design.
Topics: DuetWifi, bondtech_bmg, stl, direct_drive_extruder, delta_effector, The_Orbiter, extruder,...
5
5.0
Mar 3, 2021
03/21
by
Will Lee (LeeIIIWill)
data
eye 5
favorite 0
comment 0
Downloaded the other smart effector mounts for the 5015 radial fan but they got in the way of the effector arms when utilizing the space on the sides of the bed. I've been using this part fan for a few months without issue. Good overhangs and print quality so far. Designed around my F360 Smart effector model: https://www.thingiverse.com/thing:3229215
Topics: Duet_Smart_Effector, delta_effector, Duet3D, part_cooling_duct, 3D Printer Parts, Duet,...
6
6.0
Mar 17, 2021
03/21
by
Christian Petry (christian_p)
data
eye 6
favorite 0
comment 0
I wasn't happy with the cooling performance of the conventional fan duct on my Smart Effector. Especially on small parts the air wasn't coming close enough th to nozzle tip to effectivly cool the part, additionally the cooling effect was different on all sides of the model. Design goals: - airflow as close as possible at the nozzle - equal cooling on all sides - simple mounting, if possible single part design - include 40mm hotend fan adapter for silent operation It's a single part print...
Topics: delta_effector, effector, Smart_effector, 3D Printer Parts, Duet3D_Case, delta_printer, stl,...
3
3.0
Jun 7, 2021
06/21
by
Frederic Lecomte (Elescar)
data
eye 3
favorite 0
comment 0
Le tutoriel contient les instructions nécessaires pour installer un Smart Effector dans une une Anycubic Predator contenant déjà une Duet 2 Wifi. V1.1: - Correction dans les instructions de calibration, le fichier config-override.g ne doit pas être présent avant de faire la calibration - Modification du Start script dans S3D Les instructions pour installer une Duet 2 Wifi se trouve ici : https://www.thingiverse.com/thing:4111867 Support pour DuePanel 7 inches:...
Topics: delta_3D_printer, Anycubic, delta_effector, Anycubic_Delta, smarteffector, thingiverse,...
5
5.0
Mar 4, 2021
03/21
by
Philip S. (Reckham)
data
eye 5
favorite 0
comment 0
Because there are not that many smart effector 5015 blowers and I wanted to print more with PETG, I decided to make my own blower. The 5015 blower is mounted similiar to a Tevo Little Monster Radial Blower, but has a lot more power. Very nice for PETG to avoid stringing. For printing temperatures around 205°C I recommend a cooling fan speed of about 35% and fan speed of 0% for the first layer. UPDATE: 30.12.2018: - added improved version v2: - 3mm lower, better mounting and much lighter Setup:...
Topics: Duet_Smart_Effector, E3D_v6, 5015, volcano, Blower, duetwifi, 3D Printer Parts, Duet, pcb_mount,...
6
6.0
Jan 20, 2021
01/21
by
Gareth Price (bobblejot)
data
eye 6
favorite 0
comment 0
## Part Fan Shroud. ### Duet3D Smart Effector. ---------------------------------------- [Bobblejot Website](http://bobblejot.com) [Bobblejot GitHub](https://github.com/Bobblejot/) [Bobblejot Twitter](https://twitter.com/bobblejot) [Bobblejot Patreon](https://www.patreon.com/join/bobblejot?) ---------------------------------------- Needed a new part fan shroud for the brilliant Duet Smart Effector, Have plenty of 40mm 24vdc fans laying around so decided to knock up something that would hopefully...
Topics: part fan duct, 3D Printer Parts, due3d smart effector, Duet3D, smart effector, thingiverse, fan...
6
6.0
Jun 20, 2021
06/21
by
Gareth Price (bobblejot)
data
eye 6
favorite 0
comment 0
## Fan Shrouds. ### Tusk Part Fan Shroud. ---------------------------------------- [Bobblejot Website](http://bobblejot.com) [Bobblejot GitHub](https://github.com/Bobblejot/) [Bobblejot Twitter](https://twitter.com/bobblejot) [Bobblejot Patreon](https://www.patreon.com/join/bobblejot?) ---------------------------------------- Re-mixed my original part fan shroud to use Tusks. That's all nothing else. Jig for tusk hole spacings is included. [Original Fan...
Topics: effector, delta, Duet_WiFi, part_fan_shroud, thingiverse, Part_Fan, Duet_Smart_Effector,...
3
3.0
Mar 26, 2021
03/21
by
Zesty Technology (ZestyTech)
data
eye 3
favorite 0
comment 0
This adapter is specifically to mount the Nimble V2 on the very smart PCB effector that Escher3D is developing with Think3dPrint3d. It uses a hot end mount that is developed by E3D. Have a look at the effector [here.] (https://duet3d.com/wiki/Smart_effector_and_carriage_adapters_for_delta_printer) In regards to the nut used to mount the hot end to the Smart Effector. There are two sizes of nuts used, unfortunately. 19 mm Across the Flats (AF) and 17 AF. Pick the right one. Simply bolt the...
Topics: stl, The_Zesty_Nimble_V2, Nimble_V2, The_Nimble, Extruder, Adapter, Smart_effector, thingiverse,...
4
4.0
Jan 5, 2021
01/21
by
Nikolai Schauer (nikscha)
data
eye 4
favorite 0
comment 0
This solution allows for strong and lightweight cooling: Inspired by Berd-Air, fresh (cold) air is pumped to the "bracket" that mounts to the smart effector. There the air stream is split into two brass tubes which direct the air into the "nozzle". The minimal design reduces inertia of the print head and in case of a crash, only a single part (which doesn't require cooling to be printed) needs to be replaced. I use 2.5mm(od) brass tubing, cut down to a length of 46mm. A...
Topics: mosquito, stl, cooling_duct, smarteffector, tusk, Berd-Air, delta_effector, 3D Printer Parts,...
5
5.0
Mar 18, 2021
03/21
by
Max Nitschke (MacNite)
data
eye 5
favorite 0
comment 0
I really liked the design of the Kossel carriage bei 3DPB. But it seems he lost his "source files". So I re-created the desing for my Kossel built using the Duet Smart effector and Haydn Huntleys Magnetic Rod-Ends (or at least the "balls" from Haydn). I hope this might help some people. The design is for MGN12H carriages (mounting holes 20x20mm).
Topics: Linear, effector, magnetic_rod, smart, Hiwin, duet, DuetWifi, kossel, magball, carriage, Delta,...
4
4.0
Aug 9, 2021
08/21
by
Zesty Technology (ZestyTech)
data
eye 4
favorite 0
comment 0
This adapter is designed to mount the Flex on the very smart PCB effector that Escher3D is developing with Think3dPrint3d. It uses a hot end mount that is developed by E3D. Have a look at the effector [here.](https://duet3d.com/wiki/Smart_effector_and_carriage_adapters_for_delta_printer) #####Changelog: - Initial release - 1: Added the 19mm nut version and cleaned up the 17mm nut version The STL models are checked and optimised. The parts that need a different orientation to print properly are...
Topics: Nimble Extruder V3, Adapter, thingiverse, The Flex, Duet_Smart_Effector, The Zesty Nimble V3,...
