0
0.0
Jul 25, 2021
07/21
by
Dalen Vigil (DalenVigil)
data
eye 0
favorite 0
comment 0
Guy wire rigging plate w/6.75mm center hole, 3mm guy holes. Designed to sit between sections on a telescoping antenna mast, allowing you to guy the antenna in 4 directions.
Topics: dipole_antenna, thingiverse, antenna_mount, amateur_radio, Ham_Radio, antenna, SOTA,...
0
0.0
Oct 14, 2021
10/21
by
Oleksii Zelivianskyi (alexeyzel)
data
eye 0
favorite 0
comment 0
Smaller mount I designed based on official Protek25 antenna mount STL. This mount is for analog Protek25 with Frsky XM+ receiver. Printed with TPU.
Topics: thingiverse, iflightprotek25, R/C Vehicles, protek, stl, mount, frsky, antenna_mount,...
0
0.0
May 1, 2021
05/21
by
William Witt (WillyMakit)
data
eye 0
favorite 0
comment 0
As a Ham Radio Operator, I was building a BALUN in a PVC tube, and needed a PVC end cap to accept the PL259 connector. This is designed to have the connector on the inside of the end cap and secured with #6 bolts that are about 1/2" long. This fits nicely on 1 1/4" Schedule 40 PVC pipe, and you can use regular PVC glue to attach it to the PVC pipe.
Topics: stl, Ham_Radio, pvc, antenna_mount, Electronics, thingiverse, antenna
0
0.0
Jul 22, 2021
07/21
by
Dana Harris (optikool)
data
eye 0
favorite 0
comment 0
This is the Armattan Chameleon antenna holder. This includes Immortal T and Single DJI Antenna mount.
Topics: TBS_Immortal_Antenna, armattan_chameleon, stl, R/C Vehicles, DJI_antenna_mount, thingiverse,...
0
0.0
May 1, 2021
05/21
by
Andy Gutierrez (andyvgu9)
data
eye 0
favorite 0
comment 0
Source One V3 Comms Mount ==================== Here is a mount I designed for holding my communication components on my source one V3 build. I thought maybe someone else can get some use out of my design or build off of it for their specific needs. This particular print was done with a wood PLA and I gave it 2 coats of stain. I made this with the following components in mind: - FRSKY R-SXR receiver - RDQ Mach 3 VTX The VTX is zip tied to the design (cutouts to fit zip tie between the frame and...
Topics: stl, comms, X-RSX, comms_mount, drone, vtx_mount, antenna_mount, Xquad, Mach3_VTX, mount,...
1
1.0
Jul 25, 2021
07/21
by
RC 3D Printing (RC3DPrintingFacebookGroup)
data
eye 1
favorite 0
comment 0
A simple boom antenna V mount. Printed in TPU Suitable for 3.17 mm antenna tubes or you can use it without the tubes. Needs two small zip ties. Enjoy. No supports required.
Topics: thingiverse, R/C Vehicles, antenna, Antenna_holder, antenna_mount, stl
3
3.0
Jan 6, 2021
01/21
by
Fulvio Sguazzo (badtime)
data
eye 3
favorite 0
comment 0
Remixed ICOM IC-705 antenna bracket with N connector instead a BNC and made in one solid piece
Topics: be active, stl, antenna_mount, IC-705, antenna, Qrp, thingiverse, QRP_transceiver, ICOM, DIY
0
0.0
Jul 22, 2021
07/21
by
Dana Harris (optikool)
data
eye 0
favorite 0
comment 0
This is the Armattan Chameleon antenna holder. This includes Immortal T and Horizontal DJI Antenna mounts.
Topics: TBS_Immortal_Antenna, armattan_chameleon, stl, R/C Vehicles, DJI_antenna_mount, thingiverse,...
0
0.0
May 1, 2021
05/21
by
Johann Gnd (Busyjoh)
data
eye 0
favorite 0
comment 0
Hello ! it's a remix from @TeamMistralFPV, Antenna mount for the ImpulseRC APEX HD + TBS crossfire mount. Print without support and you will get the best quality for your mount !! Supports already inluded for easy printing ! You can customize it with Moustaches, just choose your color and put it on both side ! Fancy ! If you like it : TIP ! Thank you guys, nice fly ! Gopro 8 Mount Moustache Edition available ! look at my designs.
Topics: stl, crossfire, SMA, Tbs_crossfire, DIY, apex, antenna_mount, fpv, thingiverse, ImpulseRC,...
0
0.0
Jul 22, 2021
07/21
by
David Jones (DaveFridayJones)
data
eye 0
favorite 0
comment 0
SMA style antenna mount for your analogue video system, slides over the two rear Seeker standoffs and holds your antenna in place at 45deg. Print from TPU or similar flex material. Optimised for a 0.4mm nozzle, most parts of the print are completely filled with 2 or 3 walls, so printing at 100% is easiest.
Topics: stl, R/C Vehicles, fridayfpv, antenna, SMA antenna mount, thingiverse, fridayfpvseeker,...
0
0.0
Apr 24, 2021
04/21
by
David Shaddix (FlyHighFPV)
data
eye 0
favorite 0
comment 0
Custom SMA Antenna Tial mount for the Armattan Rooster with Immortal T for TBS Crossfire, and room for your battery leads to come out the top. Send me a message if you need this altered or something different entirely, I love doing custom quad parts, remixes, and prints. I''m currently on a mission to add skidz to every armguard ;) You can find me on Instagram @FlyHighFPV or youtube.com/FlyHighFPVdrone
Topics: tbs, teamblacksheep, immortal_t, crossfire, Antenna, crossfire_antenna, armattan, stl, Immortal,...
1
1.0
May 1, 2021
05/21
by
Kristian Stemsrud (Krisstems)
data
eye 1
favorite 0
comment 0
This is a vtx holder for the TBS ground station. Hole for the mounting screw is 1mm too small and needs to be drilled out.
Topics: stl, TBS_Unify, antenna_mount, Electronics, vtx_holder, TBS_unify_mount, fpv, TEAMBLACKSHEEP,...
0
0.0
May 1, 2021
05/21
by
Tim Walter (DisruptiveChaos1)
data
eye 0
favorite 0
comment 0
These two parts allow an NMO antenna fixture to be installed in the front-right fender hole that originally held the AM/FM antenna on some MGBs. The parts are curved to mimic the fender curve, and the bottom piece is cut so that it can be inserted into the body cavity from above or through the wire hole below. Pay attention to the curves while installing. As with many tasks with the MGB, small fingers and infinite patience are helpful.
Topics: stl, Ham_Radio, MGB, Automotive, antenna_mount, thingiverse
0
0.0
May 1, 2021
05/21
by
James McCullough (fsociety)
data
eye 0
favorite 0
comment 0
Used with Foxeer 150MM pagoda Has passthrough for battery wires on top. Replacement piece for the pine I used for over a year. Finally designed one and works great Send me Bitcoin 1FR34KUPwgSGH1cpPkASrswuMk7YY7iJFW
Topics: stl, R/C Vehicles, thingiverse, Xilo_Phreakstyle, SMA_Antenna_Mount
0
0.0
Jan 4, 2021
01/21
by
Gyu Lin Lee (MARTIANII)
data
eye 0
favorite 0
comment 0
FPV antenna mount for TBS Triumph pro. 45 degrees 20mm tall from the top plate.(Check the length of antenna tails)
Topics: R/C Vehicles, FPV Antenna, stl, antenna_mount, TBS Triumph pro, thingiverse, fpv
0
0.0
Jul 22, 2021
07/21
by
Dana Harris (optikool)
data
eye 0
favorite 0
comment 0
This is the Armattan Chameleon antenna holder. This includes Immortal T, Single DJI Antenna mount and GPS.
Topics: TBS_Immortal_Antenna, armattan_chameleon, stl, R/C Vehicles, DJI_antenna_mount, thingiverse,...
0
0.0
Aug 8, 2021
08/21
by
Vladimir Perevalov (maxbl4)
data
eye 0
favorite 0
comment 0
Two options for 2.4Ghz antenna mount, size is for Happy Model small antenna, but TPU can stretch and take a bit bigger antennas. You can print smaller one to put under existing camera mount, or print whole integrated mount
Topics: rekon_5, rekonfpv, thingiverse, rekon5, R/C Vehicles, fpv, stl, antenna_mount
0
0.0
Mar 10, 2021
03/21
by
Roeland Drupsteen (DutchRC)
data
eye 0
favorite 0
comment 0
Halloa :) soooo in my first flight with the Kopis mini with Caddx Vista I ripped of the FPV / RC antenna ;) The quad did not come with a really good way of mounting it.. So I drew up this mount.. It is basically a cut-to-length design.. If you want it to be shorter cut a piece of.. The way I drew it up, you will be using the maximum length of the Cherry antenna.. Printed it without supports in TPU
Topics: DJI_FPV, caddx_vista, R/C Vehicles, stl, thingiverse, antenna_mount, holybro, Kopis_mini
0
0.0
May 1, 2021
05/21
by
Daniel Douglas (DrNopants)
data
eye 0
favorite 0
comment 0
This is an antenna mount for my QAV105. But the hole spacing for mounting is 20mm so it can work for quite a few applications. No supports needed.
Topics: stl, FPV_Antenna, antenna_mount, fpv, thingiverse, R/C Vehicles
0
0.0
Apr 8, 2021
04/21
by
Russell Stutzman (rustutzman)
data
eye 0
favorite 0
comment 0
This thing was made with Tinkercad. Edit it online https://www.tinkercad.com/things/4FstEYgfpwt The V2 model is a little heavier walled. The wire runs are a little longer too so if your antenna wire is already tight that be a problem.
Topics: FrSky_X8R, Antenna_Mount, stl, thingiverse, R/C Vehicles, Wild_Thumper
0
0.0
Jul 22, 2021
07/21
by
Dana Harris (optikool)
data
eye 0
favorite 0
comment 0
This is version 2 of my SMA and Immortal T antenna holder for Gecko 3 and 4 inch drone.
Topics: TBS_Immortal_Antenna, SMA_Antenna_Mount, armattan_gecko, stl, R/C Vehicles, thingiverse
0
0.0
Apr 4, 2021
04/21
by
Ryan Gingerich (nonaym)
data
eye 0
favorite 0
comment 0
After looking into ways to improve my cheap OTA TV antenna reception, I took a little time this past weekend to design and 3D print this little adapter that allows a cheap flat OTA TV antenna to be mounted in place of the original cone of an unused DirecTV satellite dish. We’ve had this old DirecTV dish just sitting up above our garage doing nothing for the past few years since we moved into this place… so I attached a cheap antenna using this custom adapter, pointed the dish towards the...
Topics: thingiverse, free-tv, OTA, antenna, stl, freetv, over-the-air, DIY, antenna_mount, television
0
0.0
Apr 24, 2021
04/21
by
Lykourgos Danellis (Hobbytrip)
data
eye 0
favorite 0
comment 0
tbs triumph pro mount for your Apex
Topics: tbs, 3D Printing, stl, antenna_mount, thingiverse, Apex, Apex antenna mount
0
0.0
May 1, 2021
05/21
by
Dana Harris (optikool)
data
eye 0
favorite 0
comment 0
This is a redesign of my DJI Badger and Marmotte antenna mount https://www.thingiverse.com/thing:4740625 and includes a GPS mount. 3-21-21 - Updated model to make easier insertion of antennas.
Topics: stl, armattan_marmotte, TBS_Immortal_Antenna, DJI_antenna_mount, gps_mount, thingiverse, R/C...
0
0.0
Apr 24, 2021
04/21
by
Fabrizio Fiorucci (fiorucci)
data
eye 0
favorite 0
comment 0
This is a V-dipole antenna bracket to capture NOAA satellite images using Raspberry-NOAA (https://github.com/reynico/raspberry-noaa) The dipole is made using a 5mm diameter full aluminium rod. Each half is 534 mm long. Full description is available at: https://www.rtl-sdr.com/simple-noaameteor-weather-satellite-antenna-137-mhz-v-dipole/ This bracket can be screwed to a mounting pole using the two 3mm holes at its base. Print quality is fine using a 0.24mm layer height, this must be printed...
Topics: dipole_antenna, NOAA_Satelite, antenna, stl, 137MHz, thingiverse, Electronics, antenna_mount
0
0.0
Mar 16, 2021
03/21
by
Derek Stewart (Propwashfpv)
data
eye 0
favorite 0
comment 0
So this is a remix of a couple parts found here on Thingiverse, however it will not allow me to display that in the typical fashion. The first part was the Geprc Phantom Crossfire "L" Antenna holder by MTopp on August 29, 2020, https://www.thingiverse.com/thing:4582717 The second was the GEPRC Phantom XT30 by RobertS71 September 06, 2019, https://www.thingiverse.com/thing:3847623 I also added a small holder for the vtx antenna, Printed in TPU 100% infill.
Topics: FPV_Antenna, geprc, vtx_antenna_holder, dji_phantom, diversity, thingiverse, TPU, micro, vtx, Toy...
0
0.0
May 1, 2021
05/21
by
Davide Mele (Kunnuck)
data
eye 0
favorite 0
comment 0
Aliexpress apex clone sma holder + immortal t mount thicc version
Topics: stl, Immortal_T, apex, antenna_mount, aliexpress, sma, thingiverse, ImpulseRC, R/C Vehicles, thicc
0
0.0
Jul 22, 2021
07/21
by
Dana Harris (optikool)
data
eye 0
favorite 0
comment 0
This is the Armattan Chameleon antenna holder. This includes Immortal T, Vertical DJI Antenna mounts and GPS.
Topics: TBS_Immortal_Antenna, armattan_chameleon, stl, R/C Vehicles, DJI_antenna_mount, thingiverse,...
0
0.0
Mar 16, 2021
03/21
by
ISMAEL GONZALEZ GONZALEZ (Vinylias)
data
eye 0
favorite 0
comment 0
ImpulseRc apex Antenna Caddx Vista Analog Version
Topics: 3D Printing, thingiverse, Impulse_RC, Impulse_RC_Apex, stl, impulserc_apex, djifpv, antenna_mount,...
0
0.0
Apr 4, 2021
04/21
by
Benjamin Blackburn (NorthernMonkey069)
data
eye 0
favorite 0
comment 0
ImpulseRC Apex HD Caddx Vista Antenna Mount
Topics: thingiverse, R/C Vehicles, Apex, caddx, impulsehd, stl, antenna mount, Apex HD, vista
0
0.0
May 1, 2021
05/21
by
LOIC BOYER (Lboy)
data
eye 0
favorite 0
comment 0
This is a version of the squirt V2 HD with dji airunit place in the middle of the frame for better gravity center.
Topics: stl, Shendrones, Shendrones_Squirt, squirt_v2, dji_fpv, drone, runcam, shendrones_cinewhoop,...
0
0.0
Apr 27, 2021
04/21
by
Wholesome Circuits (wholesome_circuits)
data
eye 0
favorite 0
comment 0
TBS style three-hole SMA antenna holder for use with the Lumenier Chief FPV Racing frame. This is a lightweight and strong antenna mount for all your freestyle and racing needs. This mount is ideally used with a right-angle SMA adapter. I use the Lumenier AXII long stem antenna in combination with this mount for flawless video.
Topics: thingiverse, tbs_antenna, tbs, Lumenier, stl, antenna_mount, R/C Vehicles, fpv, Lumenier_Chief
0
0.0
May 1, 2021
05/21
by
Redux Air (ReduxAir)
data
eye 0
favorite 0
comment 0
The parts I use in a raven build are RAVEN-45-LOW.STL and turtle-fin.STL. If you want to use an SMA antenna you can use the file sma-mount.STL. If you want a variable nano camera mount you can use the file camera-mount.STL.
Topics: stl, fpv_racer, turtle_mode, Foxeer_Predator, antenna_mount, camera_mount, thingiverse, R/C Vehicles
0
0.0
Jul 22, 2021
07/21
by
Dana Harris (optikool)
data
eye 0
favorite 0
comment 0
This is the Armattan Chameleon antenna holder. This includes Immortal T and Vertical DJI Antenna mounts.
Topics: TBS_Immortal_Antenna, armattan_chameleon, stl, R/C Vehicles, DJI_antenna_mount, thingiverse,...
0
0.0
Jul 22, 2021
07/21
by
Grant Crockford (grrrcro)
data
eye 0
favorite 0
comment 0
Portable Yagi Uda Parts ================== I used these parts to build a Yagi Uda based on M0UKD's design, but these bits can be adapted to any design. M0UKD design is published at: https://m0ukd.com/homebrew/antennas/144mhz-2m-portable-yagi-vhf-beam-antenna/ Other Parts Required ---------------- * Boom: 15mm square x 2mm WT aluminium box section. * Elements: 6mm OD x 1mm WT aluminium tube * Ferrite: I used a FT140-43, but there are many ways to configure the feedpoint in a yagi. * Coax: Short...
Topics: vhf, yagi_antenna_mount, Yagi Uda, YAGI_INSULATOR, stl, yagi_antenna, Electronics, thingiverse,...
0
0.0
May 1, 2021
05/21
by
CJ Fox (Foxman45)
data
eye 0
favorite 0
comment 0
I made this antenna holder custom for my pc but if it helps you go ahead and use it. My antenna is from a Tuf harddrive and I mounted it using the back screw of my PC case.
Topics: stl, Computer, antenna_mount, Computer_Accessories, thingiverse, case
0
0.0
May 1, 2021
05/21
by
JW FPV (jw_fpv)
data
eye 0
favorite 0
comment 0
Caddx Vista Antenna Mount for the TBS Source One V4 Frame. Remix of [JohnnyFFM](https://www.thingiverse.com/johnnyffm/designs/) Caddx Vista Antenna Mount: https://www.thingiverse.com/thing:4504352
Topics: stl, tbs_source_one_v4, tbs, dji_fpv, drone, antenna_mount, CADDX, team_black_sheep,...
0
0.0
May 1, 2021
05/21
by
Corvo 00 (Raven00)
data
eye 0
favorite 0
comment 0
Quad pigtail antenna mount. Designed for 5mm standoff Printed in PLA and it's actually on my quad :)
Topics: stl, fpvantenna, drone, Quadcopter, antenna_mount, thingiverse, antenna, R/C Vehicles
0
0.0
May 1, 2021
05/21
by
(PeculiarHumanBiped)
data
eye 0
favorite 0
comment 0
Universal TBS Immortal-T Antenna Mount (20mm). I have used it for my Armattan Marmotte but can be used for every frame which provides 20 mm stack mounts.
Topics: stl, Immortal_T, 20mm, antenna_mount, thingiverse, tbs, R/C Vehicles, universal_mount
1
1.0
May 1, 2021
05/21
by
Flemming Delfs (Flemobil)
data
eye 1
favorite 0
comment 0
I designed receiver and antenna holder for the iFlight Nazgul V2 / iFlight XL5 V4 Frame by myself
Topics: stl, caddx_vista_antenna, iflight_nazgul, antenna_mount, iflight_xl5, FPV_Antenna_mount, iFlight,...
0
0.0
Jul 22, 2021
07/21
by
Dana Harris (optikool)
data
eye 0
favorite 0
comment 0
This is the Armattan Chameleon antenna holder. This includes Immortal T, Horizontal DJI Antenna mounts and GPS.
Topics: armattan_chameleon, TBS_Immortal_T, stl, R/C Vehicles, DJI_antenna_mount, thingiverse, gps_mount
0
0.0
May 1, 2021
05/21
by
YANNICK MULLER (F1NSR)
data
eye 0
favorite 0
comment 0
Insulator for yagui antenna boom 20 mm element diamèter 10mm distance between boom and element 5.75mm length 60 mm width 18 mm height 25 mm Screw 4 mm
Topics: stl, 144 MHZ ANTENNA, Ham_Radio, Antenna_holder, VHF ANTENNA, antenna_insulator, yagi_antenna, 2M...
0
0.0
Mar 15, 2021
03/21
by
Fabian Steiner (TryStoneDesigns)
data
eye 0
favorite 0
comment 0
This is my TBS Tracer mini T antenna mount. It is made for the back of your Quad (for Standoff-type frames). You have to print it with TPU or another very flexible material, otherwise, you won't be able to install the antenna. Installation is simple, just bend the printed part and snuggle the antenna in. The mount is a friction-fit based design for frame standoffs with a diameter of 6 mm. The distance between the center of the standoff holes is 22 mm. Feel free to use or remix this design.
Topics: Antenna_holder, 3D Printing, tbs, thingiverse, TBS_Tracer, Tracer, iFlight, immortal_t_mount,...
0
0.0
May 1, 2021
05/21
by
Zai West (bonzailyte)
data
eye 0
favorite 0
comment 0
Radiomaster TX16s EZprint SMA Antenna Mod Plate
Topics: stl, TX16S, Radiomaster_TX16s, antenna_mount, small, thingiverse, antenna, R/C Vehicles
0
0.0
Mar 10, 2021
03/21
by
Nicolas Barrière (nbarriere)
data
eye 0
favorite 0
comment 0
Antenna & buzzer mount for frame Anniversary Special Edition Martian 215
Topics: 2020, drone, FPV_Antenna, fpv_racer, martian_220mm, Drones, R/C Vehicles, stl, thingiverse,...
0
0.0
Jul 25, 2021
07/21
by
Dalen Vigil (DalenVigil)
data
eye 0
favorite 0
comment 0
Guy wire rigging plate w/13mm center hole, 3mm guy holes. Designed to sit between sections on a telescoping antenna mast, allowing you to guy the antenna in 4 directions.
Topics: dipole_antenna, thingiverse, antenna_mount, amateur_radio, Ham_Radio, antenna, SOTA,...
0
0.0
May 1, 2021
05/21
by
Burnout Cheng (burnout12603)
data
eye 0
favorite 0
comment 0
These are Landing accessories for the TBS Souce One frame. The landing wrack(skid) thickness is 1.5mm. The GPS mount is designed to fit the Matek M8Q-5883 GPS+Compass. It is intended to assemble the VTX antenna pigtail connector from the back to front and screw fix with M3 screws. Please do not hesitate to show me some love if you like my work! Suggerstions are also very welcomed! Thank you~
Topics: stl, Landing_Gear, vtx_antenna_mount, DIY, gps_holder, Runcam_mini_mount, Landing_Skids, gps_mount,...
0
0.0
May 1, 2021
05/21
by
Sercan Tavas (Klomboz)
data
eye 0
favorite 0
comment 0
Gps and Receiver holder for Iflight Nazgul5 Compatible with BN-880 Gps
Topics: stl, iflight_nazgul, GPS, gps_holder, nazgul5, antenna_mount, iflight_xl5, gps_mount,...
0
0.0
Mar 10, 2021
03/21
by
Mee KaaH (meekaah)
data
eye 0
favorite 0
comment 0
can flex inward or outward to accept standoff width ranging between ~19mm and ~32mm You can copy and edit this design on OnShape https://cad.onshape.com/documents/7e15220de24f33ab70ba6be5/w/7f0819db393c16caf149efe5/e/f627897dc6ad8005c8ea6640
Topics: quadcopter, caddx_vista, R/C Vehicles, stl, thingiverse, antenna_mount, fpv, antenna, dji_fpv
0
0.0
May 1, 2021
05/21
by
yasin alberto masry pastor (yasinalberto)
data
eye 0
favorite 0
comment 0
SMA antenna mount for geprc mark4 HD frame, is for double antenna.
Topics: stl, Antenna_holder, tpu_mount, mark4, geprc_mark4, FPV_Antenna, TPU, antenna_mount, R/C Vehicles,...
