3
3.0
Mar 4, 2021
03/21
by
Anthony t0t0 (t0t0)
data
eye 3
favorite 0
comment 0
It is a remix of this nice canopy to add the possibility to use the extra hole on the 65/75 pro 2 frame and 85X frame. By doing that it will avoid to break the hole that maintain the FC board and it is more stronger ! So you can use it for: - BetaFPV 75 pro 2 - BetaFPV 65 pro 2 - BetaFPV Beta85X (non HD) for the following camera: - CADDX EOS2 - Z02 (the stock one) by printing the extra piece More information here: https://www.t0t0.fr/2019/02/26/beta75-pro-2-mods/
Topics: stl, R/C Vehicles, beta85x_canopy, betafpv, beta85x, thingiverse
3
3.0
Mar 5, 2021
03/21
by
THUG FRAMES (THUG3D)
data
eye 3
favorite 0
comment 0
I have another pod listed that I altered and for the reasons in the vid listed but after flying I wanted less camera angle for real slow cinewhoop style filming. Hence I made this POD - its not altered from anyone elses, its a fresh design - the other is great for fast flying but this is the one for the real cinewhoop style footage... It has - less angle for slower flying - 8mm lower than the other pod - super easy to remove and fit - for Cinewhooping with the 85 at slow speeds this is the pod...
Topics: beta85x_HD, stl, beta85x_canopy, R/C Vehicles, betafpv, beta85x, thingiverse
3
3.0
Mar 9, 2021
03/21
by
joppa ngo (ahpaa)
data
eye 3
favorite 0
comment 0
A more balanced canopy which shifts the HD cam forward. Better for slow cine flights? Less camera angles on this canopy. Relieves cam cable being crimped to the HD board as the cam is further forward and slightly higher. Weighs 1g heavier then stock design. Parametric model. To mount: Thread the cam into the canopy but don't bolt on. When done mounting electronics. Upon screwing in canopy shift the camera out through the front to expose the 3rd screw (front of craft) and screw down. Then bolt...
Topics: beta85x_HD, R/C Vehicles, stl, thingiverse, beta85x, beta85, beta85x_canopy
4
4.0
Mar 8, 2021
03/21
by
jose luis ortiz (JLOrtiz)
data
eye 4
favorite 0
comment 0
He añadido un soporte extra para atornillar la placa de la caddx por la parte trasera, bajado la inclinación de la cámara, modificados tornillos de sujeción de la cámara para que pueda bajarse la inclinación y un poquito mas alto que el original. Yo lo estoy imprimiendo en Polipropileno al 100% de relleno y 0,2 de altura de capa. Gracias a mi queridisima Andreea por ayudarme en la modificación.
Topics: beta85x_HD, canopy, CineWhoop, betafpv, stl, thingiverse, beta85x, beta85, Other, caddx_turtle,...
4
4.0
Mar 18, 2021
03/21
by
Henry Chung (pathfinderzero)
data
eye 4
favorite 0
comment 0
Betafpv 85x HD Canopy This is a remix of Betafpv 85x HD Canopy. Changes include 1) Added front and back screw mounting holes to better secure the canopy to the frame and to reduce vibration/jello. (Note: For the VTX, route your VTX wires around the sides of the rear standoff). 2) Increased the height of canopy to give more room between Caddx Turtle camera and PCB board. This is to minimize damage to the cable and the PCB board. You can also fit a regular Caddx Turtle with the camera backplate....
Topics: R/C Vehicles, beta 85x, betafpv, betafpv 85X, canopy, stl, thingiverse, betafpv 85, beta85x,...
