2
2.0
Mar 31, 2021
03/21
by
Garry Keogh (GryKyo)
data
eye 2
favorite 0
comment 0
This part is designed to worm through a 32mm diameter hole in a sheet aluminium vented soffit. This mount is customised for the Reolink B800 bullet camera but the concept would work for any camera where a strong mounting is needed in thin or soft sheet metal. The mount has three pillars to suit the (Reolink) supplied self tapping screws which will get little purchase on the thin soffit material. This 3D print twists through a hole in the soffit and has a position to hook a small wire or cord to...
Topics: thingiverse, camera_mount, security_camera, CCTV, DIY, security_camera_mount, stl
3
3.0
Jun 6, 2021
06/21
by
Dmitry Rechkin (FlexRC)
data
eye 3
favorite 0
comment 0
Micro (19mm wide) and Mini (22mm wide) FPV camera mounts for FlexRC Colugo Freestyle / Proximity frame that can be used with dual 20x20 stack or single 30.5x30.5 stack of any height as well as 3-4" replaceable arms and optional Bumper configuration.
Topics: flexrc, thingiverse, DIY, stl, camera_mount, FlexRC_Colugo, fpv_camera_mount
2
2.0
Jun 11, 2021
06/21
by
Sławomir Pietrzykowski (Painted_Bird)
data
eye 2
favorite 0
comment 0
A thru-wall mount for OV5647 camera for RaspberryPi. Allows for the usage of the camera on both sides of the mount. Requires 4x fi 3 and 4x fi 2 mm screws with nuts for mounting. Theoretically, it allows for the usage of 3.5 mm and 2.0 mm screws. However, I'm not too fond of the tolerances of the holes on the camera module.
Topics: Robotics, camera_mount, thingiverse, rpi_camera_mount, raspberry_pi_camera, stl
9
9.0
Jan 10, 2021
01/21
by
Kevin Mahoney (zenotec)
data
eye 9
favorite 0
comment 0
S500 frame attachment for mounting a forward facing FPV camera like the Run Cam.
Topics: R/C Vehicles, thingiverse, stl, S500, camera_mount, fpv_camera_mount
8
8.0
Mar 10, 2021
03/21
by
Rcflying Fil (RcflyingFil)
data
eye 8
favorite 0
comment 0
A housing in 3 pieces to mount the mini camera like your own mounting method. Angle of the camera is adaptive according your fpv-vehicle, quad, plane, car..... I wanted a small case to protect the camera lens and electronics on my micro-quad, mine snaps together and stays. I use Repieter host with Cura to slice which gives a remarque the the design is not waterproof, but in print is this not a problem. Just a small 3mm bolt or a zip-tie and you are ready to rumble. Have fun and enjoy the housing
Topics: fpv_camera_mount, stl, thingiverse, rcflying fil, camera mount, mini fpv camera mount, quanum...
6
6.0
Jun 11, 2021
06/21
by
(jo_fpv)
data
eye 6
favorite 0
comment 0
Summary ... ...
Topics: fpv, Xaomi, camera_mount, camera, thingiverse, fpv_camera_mount, fpv_racer, stl
2
2.0
Jan 7, 2021
01/21
by
Chi Woodruff (cwood)
data
eye 2
favorite 0
comment 0
My modification to the Source One Cam Plate. I got tired if the cheap camera adapters that seem to shatter on heavy impacts. I designed this around the dji camera but it should fit most mini cams that are around 20mm wide.
Topics: R/C Vehicles, camera_mount, tbssourceone, stl, thingiverse, fpv_camera_mount, sourceone
3
3.0
Apr 20, 2021
04/21
by
Dima Tsvetkov (DiAleksi)
data
eye 3
favorite 0
comment 0
Camera mount for [13x13mm LDARC](https://www.banggood.com/800TVL-150-Degree-Camera-For-Kingkong-Tiny6-Tiny7-Micro-FPV-RC-Quadcopter-p-1144173.html?p=MW151810738534201705) or such to mount onto BetaFPV brushless frame in low profile builds. Currently, I have a 15, 20 and 25-degree angle mount. *2019-03-13 Update:* Added 20 and 25-degree anges Ask me for other angles.
Topics: thingiverse, stl, R/C Vehicles, tiny_whoop, camera_mount, fpv_camera_mount
4
4.0
Apr 27, 2021
04/21
by
Norm Nicastro (Norm202)
data
eye 4
favorite 0
comment 0
This camera doesn't come with a tripod mount. Only a wall or ceiling mount. This solves that problem. use super glue to secure nut. This thing was made with Tinkercad. Edit it online https://www.tinkercad.com/things/0jd17hxLY8I
Topics: thingiverse, camera_adapter, camera, stl, camera_mount, fpv_camera_mount, 3D Printing
4
4.0
Mar 17, 2021
03/21
by
Zach Nemitz (PaperScarecrow)
data
eye 4
favorite 0
comment 0
Recently picked up a used Sony HDR-AS200V action camera and loved the size, but hated that the mounts were proprietary and hard to find. I already had a helmet mount kit for my gopro and wanted to re-purpose it for the action camera, but the existing models I found here didn't quite work for my model and use case. Here's a really simple, strong, and quick to print mount that will let you use an HDR-AS200V (and potentially other sony action cameras) with standard gopro blade mounts. It uses the...
Topics: camera_adapter, stl, camera_mount, GoPro_Mount, helmet_camera_mount, thingiverse, helmet_mount,...
2
2.0
Mar 26, 2021
03/21
by
Green Racoon (AzSaSiN)
data
eye 2
favorite 0
comment 0
SLA Printer Elegoo Mars Camera mount and led\buzzer frame mount **Frame:** [Pipi Shrimp Mini XS5 220 220mm Carbon Fiber Quadcopter Frame Kit w/ 4mm arm](https://www.amazon.com/Pelusa-220mm-Wheelbase-Carbon-Racing/dp/B0797NSDKB/ref=sr_1_2?keywords=xs+5+220&qid=1574275694&s=toys-and-games&sr=1-2) **Camera:** **Buzzer/LED:** [Drone LED with Buzzer HGLRC 5V LED...
Topics: stl, mount, drone, fpv_camera_mount, thingiverse, camera_mount, Hobby, fpv_camera
7
7.0
Jun 20, 2021
06/21
by
Ian Murchison (ianmurchison)
data
eye 7
favorite 0
comment 0
This is a 30deg mount for the Eachine EF01. I was doing a 3" build and needed something, I decided to use the standoffs as my main anchor point. Surfacing is quick and dirty but it works. The camera is simply held in with hot glue however an elastic could also be used. Designed for ========== This will work for the Eachine EF01 AIO VTx + Camera module without the case one. I had an AIO unit off of a QX95 that also fit in this, but this file specifically has openings for the EF-01. The...
Topics: fpv_camera_mount, R/C Vehicles, thingiverse, stl, fpv, camera_mount, Eachine
4
4.0
Mar 9, 2021
03/21
by
liam carter (UK3DPrintz)
data
eye 4
favorite 0
comment 0
camera mount to attach onto one of my gimbals, this is a 20.7mm circular hot shoe connector
Topics: hot shoe, fpv_camera_mount, stl, thingiverse, camera, Camera, camera_mount
2
2.0
Apr 5, 2021
04/21
by
Namari Namerikawa (n_namerikawa)
data
eye 2
favorite 0
comment 0
＜Webカメラ壁マウント＞ ビデオ通話時、WebカメラをPCモニターにひっかけて使用すると、下からの角度&アップで映ってしまいます このWebカメラ壁マウントを使えば正面からの角度&アップじゃなく映せるので、もうカメラの角度に困りません！ 本体部分と羽部分は、接着剤等で接着することをおすすめします。
Topics: thingiverse, Camera, camera_mount, stl
8
8.0
Jan 10, 2021
01/21
by
AARON ZIA (cmdctrl)
data
eye 8
favorite 0
comment 0
added diamond plate to the pistol grip.
Topics: Camera, thingiverse, camera_mount, stl
5
5.0
Jan 20, 2021
01/21
by
RC Pilot Multirotor (FPV_Pilot)
data
eye 5
favorite 0
comment 0
ZMR 250 - Blackout Frame Universal Action camera mount for vibration dampeners. With up tilt.
Topics: camera mount, Hobby, stl, thingiverse
1
1.0
Sep 13, 2021
09/21
by
Mad Hatter (MadHatterElectronics)
data
eye 1
favorite 0
comment 0
Two-hole mount for Circle camera 2 from Logitech. Slide-in place mount instead of the original snap-in.
Topics: stl, camera_mount, thingiverse, Other
8
8.0
Apr 30, 2021
04/21
by
dursun gül (dursung)
data
eye 8
favorite 0
comment 0
camera holder for video recording. rotatable in two different axis
Topics: stl, thingiverse, Camera, camera_mount
2
2.0
Mar 16, 2021
03/21
by
Kaworu Chang (gumo_design)
data
eye 2
favorite 0
comment 0
https://youtu.be/PCrWgT9yRLc It's modularized designed in 3 parts So i can design parts for different lenses and camera systems in the future. The hardware you need is 4 pcs of M2x10 flat head screws for combining the base with bayonet and one M5x10 hex screw as a tightener for tilting part. *The fitting may be different due to the accuracy of different 3D printers so you may need to have some diy skill and tools. Hope you enjoy the design.
Topics: stl, camera_mount, Camera, thingiverse
2
2.0
May 1, 2021
05/21
by
László Cziglédszky (Namake_Mono)
data
eye 2
favorite 0
comment 0
Camera mount bracket for Canon FD 200mm f2.8 objective.
Topics: stl, thingiverse, Camera, camera_mount
1
1.0
Nov 30, 2021
11/21
by
Chris Carr (thunderbirds2017)
data
eye 1
favorite 0
comment 0
this is a camera mount for Tri Pod
Topics: Camera, thingiverse, stl, camera_mount
2
2.0
Jan 18, 2022
01/22
by
John Fierst (Mercuryinhell)
data
eye 2
favorite 0
comment 0
Used to hang my camera from a support beam.
Topics: stl, thingiverse, Camera, camera_mount
2
2.0
Jan 6, 2021
01/21
by
Dima Tsvetkov (DiAleksi)
data
eye 2
favorite 0
comment 0
Adapter for micro cameras. Print without supports. Check that springy pin is not jammed and moves freely when pushed. Cut foam, glue in place. Push the camera inside until it clicks and lock it with a screw on the side.
Topics: R/C Vehicles, camera_mount, stl, TBS_Caipirinha, thingiverse, fpv_camera_mount
3
3.0
Apr 8, 2021
04/21
by
Stuart Townsend (5tuTown95)
data
eye 3
favorite 0
comment 0
The mount i use for my SJ1000 camera on my helmet, will need 5mm nuts and bolts and some of this - Black SJ3540 (250) 3M Dual Lock Tape (Amazon) to attach to helmet. I use it come rain or shine no problems. I suggest that you hold the part on your helmet whilst still hot (heated bed) to get a good fit up.
Topics: adjustable, motorcycle, helmet_mount, Camera, helmet_camera_mount, camera_mount, stl, thingiverse
7
7.0
Apr 17, 2021
04/21
by
Finn Harms (innif)
data
eye 7
favorite 0
comment 0
This is a clone of the Onepaa x2000 camera mount. For me it works very well.
Topics: thingiverse, Action_Cam, fpv_camera_mount, stl, Onepaa, camera, camera_mount, Camera
8
8.0
Jan 14, 2021
01/21
by
Kostyantin Ignatov (KostyaIgnatov)
data
eye 8
favorite 0
comment 0
Foxeer Arrow V3 camera mount for Lantian 215 Items must be right and the left. !!!It should mirror your in your slicer !!!
Topics: Foxeer, thingiverse, Hobby, stl, foxeer_arrow, lantian, camera_mount, fpv_camera_mount
6
6.0
Jan 17, 2021
01/21
by
dave spencer (davesonfire43)
data
eye 6
favorite 0
comment 0
I built this to hold my SLR without having to carry around a tripod. With a cheap strap it can be attached to a tree, telephone pole, handrail or just about anything. Print multiple arms if required. You will need to buy some 1/4 x 20 carriage bolts and wing nuts as well as 1 1/4 x 20 bolt to hammer into the thumbwheel so you can attach your camera. Be sure all parts are printed with the round gear teeth facing up.
Topics: Camera, camera_mount, stl, thingiverse
2
2.0
Mar 26, 2021
03/21
by
Daniel Bonina (dbonina)
data
eye 2
favorite 0
comment 0
Wall mount support for mini dome camera
Topics: stl, Camera, camera_mount, thingiverse
2
2.0
Mar 15, 2021
03/21
by
(cooasty)
data
eye 2
favorite 0
comment 0
Simple cam mount. 3-1/4" x 1" bolts 4- 1/4" nuts
Topics: stl, camera_mount, Camera, thingiverse
4
4.0
Mar 8, 2021
03/21
by
Luke McNeice (lukemcn)
data
eye 4
favorite 0
comment 0
Minimal, window-sucker camera amount for use with Rpi Zero + mount: https://www.thingiverse.com/thing:3558546 Modification of https://www.thingiverse.com/landshark666's https://www.thingiverse.com/thing:2874337 This thing was made with Tinkercad. Edit it online https://www.tinkercad.com/things/ha29d7SGEKO
Topics: stl, thingiverse, camera_mount, Camera
7
7.0
Mar 22, 2021
03/21
by
Balena (balena_io)
data
eye 7
favorite 0
comment 0
This is a small support to align the raspberry pi camera in the center of the fake surveillance camera.
Topics: thingiverse, Camera, stl, camera_mount
5
5.0
Mar 2, 2021
03/21
by
Ashley Farncombe (Bob68)
data
eye 5
favorite 0
comment 0
I made this because the cheap tripod that i had tipped over with the camera and broke. This bracket can be adjusted to give nearly any angle that you wish. Also it can be moved back and forward to keep the camera balanced. The holes in the base and top are 7mm, so will take a standard 1/4" bolt. The bolt handle is for a 1/4" bolt so it will be easy to tighten by hand. The picture shows the shorter supports (No.2, 75mm), but i have included 125mm (No.1). The bracket uses 12 x 4mm bolts...
Topics: thingiverse, stl, Camera, camera_mount
2
2.0
Apr 4, 2021
04/21
by
Carl Raymond (CarlRaymond)
data
eye 2
favorite 0
comment 0
Contoured hand grips, with or without a thumb button and a 3.5mm jack in the base. Build a two-handed camera stabilizing mount with a shutter release button, or a fighter plane control yoke with "pew pew" buttons. The top hole accommodates a standard 16mm diameter momentary pushbutton, such as this: https://www.amazon.com/gp/product/B07L1L5MZ3/ The bottom opening fits a 3.5mm TRS or TRRS jack, like this: https://www.amazon.com/gp/product/B06XG3YTC4/ The inside cavity has room for a...
Topics: thingiverse, Electronics, camera_mount, stl
8
8.0
Apr 17, 2021
04/21
by
tanner netterville (rennat)
data
eye 8
favorite 0
comment 0
This is a camera mount for 19mm wide runcam-swift-micro style cameras to be held between two M3 standoffs 40mm center-to-center. It includes camera angle references at 10 degree intervals from 10 degrees to 60 degrees. Here it is on my Shapeways store: https://www.shapeways.com/product/RFER5VKU4/runcam-swift-micro-mount-for-40mm-apart-standoffs?optionId=63485864
Topics: runcam_micro_swift, thingiverse, stl, R/C Vehicles, camera_mount, fpv_camera_mount
3
3.0
Apr 13, 2021
04/21
by
Rey Perez (DINGLEBERRY1)
data
eye 3
favorite 0
comment 0
ZMR Only (250 MM Quadcopter) FPV Aomway Camera Mount for ZMR Quadcopter Frame. Stationary Mount, NO Tilt! I Created this FPV AOMWAY camera mount for the HOBBYKING AOMWAY FPV system. (FPV Aomway syst can be purchased online) Will fit over 5MM (thick) & 37MM (Tall) Standoffs. (the ZMR quad normally comes with 36MM (Tall) standoffs, I purchased Black 37MM standoffs (ebay) for Color Coordinating. This 3D Model will fit the 37MM standoffs, BUT with little Modification you can make it fit the...
Topics: thingiverse, Aomway, 3D Printing, camera_mount, stl, FPV_mount, FPV, fpv_camera_mount
2
2.0
Jun 7, 2021
06/21
by
Dmitry Rechkin (FlexRC)
data
eye 2
favorite 0
comment 0
This camera mount has been designed to accommodate DJI FPV camera into FlexRC Colugo frame . It offers two positions in order to allow many various angles with nothing in the view of the camera, while still providing maximum protection for it.
Topics: flexrc, dji_fpv, thingiverse, DIY, stl, camera_mount, FlexRC_Colugo, fpv_camera_mount
1
1.0
Aug 8, 2021
08/21
by
(RealPrint)
data
eye 1
favorite 0
comment 0
Camera mount for outdoor cameras. Holes still need to be drilled. The extension is optional. (google translation) Kamerahalterung für Outdoor Kameras. Es müssen noch Löcher gebohrt werden. Die Verlängerung ist optional.
Topics: mounting_bracket, thingiverse, fpv_camera, camera_mount, fpv_camera_mount, kamerahalterung, stl,...
1
1.0
Apr 19, 2022
04/22
by
Nate Payne (MrShutterBug)
data
eye 1
favorite 0
comment 0
This is a very light canopy & camera mount for a 65mm 1S Whoop. If you have a larger build with more impact force, then I suggest you use a stiffer canopy than this. I featured this canopy in the following video about an HDZero 1S Whoop: https://youtu.be/nXgqhefFxWY Features: - Fits cameras with a 7mm wide lens. Probably also fits cameras with 8mm wide lens, but you would have to stretch the material more when inserting the lens. - Weighs less than 0.6 grams (version with no lens hood) -...
Topics: whoop, thingiverse, tiny_whoop_canopy, Whoop_Canopy, camera_mount, stl, whoop_camera_mount, R/C...
2
2.0
Mar 31, 2021
03/21
by
John Doe (3d_jedi)
data
eye 2
favorite 0
comment 0
Easy to print 5 piece WYZE CAM PAN ADJUSTABLE WALL MOUNT. easy to grab knobs easily position WYZE pan cam for ideal tilt viewing angle printed with PLA+ ...choose from selection on Amazon by Clicking Here suggest printing threaded knobs individually for ideal thread integrity Get the "WYZE Pan Cam" on Amazon by Clicking Here
Topics: security_device, camera_adapter, thingiverse, camera_mount, security_camera, camera, security,...
3
3.0
Mar 25, 2021
03/21
by
Logan Rawlins (mavericm1)
data
eye 3
favorite 0
comment 0
byeeye fpv cam from newbeedrone. This is a 30 degree camera mount that supports that camera. 1line wall this is just under 1 gram in weight and is extremely low and also prevents your cam from getting hooked on anything. Its friction fit onto the lens
Topics: stl, fpv, fpv_camera_mount, camera, thingiverse, camera_mount, fpv_camera, 3D Printing
1
1.0
Jul 22, 2021
07/21
by
Haensse (haensse)
data
eye 1
favorite 0
comment 0
Runcam 3 lite holder to mound in front of airplane behind a plate with a hole. Camera is inserted into the two half and mount is glued with superglue on the plate. Pls ensure that cap is mounted on the optic in other to protect it from super glue. Printed with 25%
Topics: holder, camera_mount, stl, R/C Vehicles, fpv_camera_mount, thingiverse, Runcam_Split
6
6.0
Jun 21, 2021
06/21
by
Adrien YOP (vinadre)
data
eye 6
favorite 0
comment 0
Cam mount for mangoose Fit fine with gopro session Need M3x8 and nut like original thing
Topics: fpv_camera_mount, Toy & Game Accessories, thingiverse, stl, camera_mount, Mongoose, Armattan...
5
5.0
Jan 21, 2021
01/21
by
Devon (devonyyc)
data
eye 5
favorite 0
comment 0
This is a camera tilt mechanism for a ZMR 250 frame. I had to play around with various wall settings before I reached this third design. The main problem was I designed this before Cura had a "print walls smaller than [nozzle size]" but now that that is an option, I have included my earlier designs in case those work for you. Exact frame I used for this design has been discontinued. (Probably for the better, simply too outdated and there are better quad frames on the market now. I...
Topics: quad, stl, ZMR250, thingiverse, Quadcopter, fpv_camera_mount, R/C Vehicles, camera_mount
2
2.0
Mar 19, 2021
03/21
by
Brandon Miura (Bmxican828)
data
eye 2
favorite 0
comment 0
30 deg Bolt on Gopro hero 7 mount for the impulse alien frame. For best results print on its side
Topics: fpv_camera_mount, camera_mount, thingiverse, Hero 7, 3D Printing, Drone, stl
8
8.0
Jan 9, 2021
01/21
by
(rieders)
data
eye 8
favorite 0
comment 0
A 600TVL Camera mount on a F450 http://www.banggood.com/600TVL-8_0MP-14-2_8mm-CMOS-FPV-170-Degree-Wide-Anlge-Lens-Camera-PALNTSC-p-984345.html?rmmds=myorder
Topics: R/C Vehicles, thingiverse, FatShark_600TVL, stl, camera_mount, fpv_camera_mount
6
6.0
Jan 16, 2021
01/21
by
Chris Johnson (Iamraw)
data
eye 6
favorite 0
comment 0
FPV Cam Mount Rev Y- Standard 30° - 60° GoPro Session Mount - Standard 25°, 35°, 45°
Topics: DE_ANUBIS, stl, thingiverse, fpv_camera_mount, gopro_session, Other, camera_mount
2
2.0
May 1, 2021
05/21
by
Dennis Norman (Bigplumbs)
data
eye 2
favorite 0
comment 0
I wanted a little go Pro Camera mount to screw fix to a timber surface where the camera points parallel to the surface you are fixing it to. I designed this little mount
Topics: stl, thingiverse, Hobby, camera_mount
8
8.0
Apr 21, 2021
04/21
by
nikolas tsr (nikolastsr)
data
eye 8
favorite 0
comment 0
This is a Magnetic Camera Mount. You attach one piece to the tripod and the other to the camera and the two pieces "clip" together. You have to put magnets inside the printed object, as well as a nut, for this to work properly.You have to pause the print, place the magnets (there are "pockets" inside the blocks) and then continue. I used small magnets with 1mm height and 12mm diameter (that was what I had). I put 2 magnets in every "pocket". There are 4 pockets on...
Topics: thingiverse, stl, camera_mount, Camera
3
3.0
Jun 11, 2021
06/21
by
(JCatRC)
data
eye 3
favorite 0
comment 0
Summary This is another remix of Atron73's Ritewing Hardcore 44 Camera mount. But I modified this camera nose mount for the Runcam Night Eagle 2 Pro (night camera) to fit on the nose of my Ritewing Hardcore 44 (LED night plane). It has a built in 5 deg camera down tilt. The camera mount lens hole ID is 17.15mm which provides a very nice snug fit (not too tight) for the Runcam 17mm lens O.D. The material is ABS 1.75mm filament at 20% fill density. The Prusa I3 MK2 temperature settings are: 255...
Topics: nose, camera_mount, runcam, thingiverse, fpv_camera, fpv_camera_mount, ritewing, ritewingrc, stl
6
6.0
Jan 19, 2021
01/21
by
Russ Squire (Desertferal)
data
eye 6
favorite 0
comment 0
I designed this to hold an SJCAM 5000 onto the gimbal on my drone using velcro tape
Topics: stl, thingiverse, sjcam_5000x, fpv_camera_mount, drone, R/C Vehicles, camera_mount
