1
1.0
Apr 20, 2022
04/22
by
Piotr Chrusciel (PiotrChr)
data
eye 1
favorite 0
comment 0
OBI Extension cord mount Optional mounts for more holding force. No support is needed.
Topics: extension_cord_holder, thingiverse, extension_cord_cover, obi_extension_cord, extension_cord,...
6
6.0
Jan 21, 2021
01/21
by
(SwiftNinjaPro)
data
eye 6
favorite 0
comment 0
A thing that hooks onto a shelf bracket, and the back of an extension cord to hold it up Note: while PLA may work, I recommend using a stronger material like ABS Recommended settings: use the build plate adhesion type, brim, to hold the print to the build plate better
Topics: extension_cord_holder, Tool Holders & Boxes, thingiverse, extension_cord, extension_cord_grip,...
4
4.0
Mar 19, 2021
03/21
by
Pekka Turunen (Pekk-O)
data
eye 4
favorite 0
comment 0
This is a holder to be hanged from a radiator to house an extension cord. The inside is 48 mm wide, it could be made 50 because this one is pretty tight for a standard size used in Finland at least. Make it as long as you need, the model is 150 mm.
Topics: extension_cord, thingiverse, electricity, Organization, extension_cord_holder, stl
9
9.0
Jan 17, 2021
01/21
by
(sunsetvette)
data
eye 9
favorite 0
comment 0
I have a couple of cars I put in storage every winter with battery maintainers(trickle chargers). The chargers are mounted under the hood year around. During the year when they are not charging I wanted a plug to cover the 110v male plug.
Topics: Automotive, Extension cord, thingiverse, Extension cord cover, plug cover, stl
3
3.0
Mar 25, 2021
03/21
by
Cor ten Hoor (Cortenhoor)
data
eye 3
favorite 0
comment 0
extension cord holder and cable clamps
Topics: stl, thingiverse, extension cord, extension cord holder, cable clamps, Household
8
8.0
Jan 3, 2021
01/21
by
vincent booth (oxford_studio)
data
eye 8
favorite 0
comment 0
This is a cover for extension cord going to RV. you need to print up two Extension cord RV and one Extension cord RV 2
Topics: stl, Vehicles, extension_cord, RV PLUG, RV extension cord, RV, thingiverse
Topics: Youtube, video, Howto & Style, StudPack, Extension cord, Extension cord repair, Extension cord...
2
2.0
Jul 22, 2021
07/21
by
Stefan Harald (stefanhar)
data
eye 2
favorite 0
comment 0
The holder is designed to be low profile to not interfere with plugs. Dimension of 41x53mm is supported by default but the part can be scaled to support smaller or bigger sockets. You can scale and print the test piece to find the correct fit then apply the same scaling to the main piece. **Dimensions (default)**: **Height**: 41mm **Width**: 53mm
Topics: holder, electric_plug_sockets, stl, multi_outlet, Organization, extension_cord_holder,...
0
0.0
Aug 14, 2022
08/22
by
shinobu takahashi (shintak)
data
eye 0
favorite 0
comment 0
A cover to prevent the plug of an extension cord from being disconnected. 延長コードの抜け止め用のカバーです。 How to use / 使い方 https://youtu.be/ZEcY71ZVQmU Print End.stl x2 ExCoveredt.stl x1 or x2 Joint.stl
Topics: Extension cord, plug, stl, Electronics, thingiverse
3
3.0
Jan 5, 2021
01/21
by
R. van Twisk (rvtwisk)
data
eye 3
favorite 0
comment 0
Orders from the boss, have to get rid of all the cables! This design allows you to mount an extension cord (you know, the 2..6 plug version) like this one (https://upload.wikimedia.org/wikipedia/commons/thumb/2/27/Extensioncord.jpg/1024px-Extensioncord.jpg) on the wall. Usually these extensions cords have on the back holes where the top and bottom are screwed together and these 'plugs' fit right into that so you can screw it on the wall, nice and hidden. Just measure the distance, offset,...
Topics: Organization, stl, wallmount, extension_cord, thingiverse
4
4.0
Apr 1, 2021
04/21
by
Ben Nemec (nemebean)
data
eye 4
favorite 0
comment 0
A replacement for the stock extension cord holder on my Snow Joe snowblower. The one the comes with it is far too small for the 12 gauge extension cord I need, and it arrived broken in any case. This one works in a similar fashion but is designed for the larger extension cord. I printed it out of PETG with 10 wall lines. I broke a couple of these printed out of PLA with less robust structure so I've done what I can to beef it up (pro tip: don't step on the extension cord). Hopefully the PETG...
Topics: extension cord, thingiverse, snowblower, Parts, stl
3
3.0
Mar 13, 2021
03/21
by
Hans Palm (hanpa)
data
eye 3
favorite 0
comment 0
Designed this to have a small format. Included a holder for the end connector of the cable instead of just letting it hang down on one of the sides, to make it easier to find it later. The screw holes have diameter 3.5 mm, countersink 90 degrees from 8 mm on top of the screw.
Topics: thingiverse, cord, extension_cord_holder, cable, extension_cord, cord_holders, Organization, stl,...
4
4.0
Apr 11, 2021
04/21
by
UWM_DCRL (UWM_DCRL)
data
eye 4
favorite 0
comment 0
This is part of our powder coating set up. We have several parts that make up the entire cart. This part is for the extension chord on the back of the cart.
Topics: thingiverse, stl, extension_cord, Tool Holders & Boxes
4
4.0
Apr 11, 2021
04/21
by
UWM_DCRL (UWM_DCRL)
data
eye 4
favorite 0
comment 0
This clip fits most extension for better chord management.
Topics: thingiverse, extenti, clip, stl, Organization, extension_cord
3
3.0
Mar 12, 2021
03/21
by
Paul Baker (Paul6833)
data
eye 3
favorite 0
comment 0
I absolutely love the Headphone Hook from mixmastermaize, and I wanted to use them for my extension cords hanging in my garage. I was concerned about the weight of the cords, so I remixed the design by adding a lower bracket with screw hole and a triangular support piece. This will hopefully support the weight of the cords.
Topics: thingiverse, extension_cord, wall_hook, Organization, stl
3
3.0
May 1, 2021
05/21
by
jang seong hun (baolab)
data
eye 3
favorite 0
comment 0
스피드랙 앵글선반에 멀티탭을 가로로 거치하고싶을때 사용할 수 있음 영어권에선 멀티탭이라고 안하고 익스텐션 코드라고하네 어차피 한국 내수용일꺼같아서 설명 한글로 적음 출력물을 멀티탭 관통홀에 맞춰 배치하고 드릴로 피스박아서 고정시켜준다 *멀티탭 1개당 출력물 2개 박아주는게 좋음 스피드랙 가로칸을 하나 뒤집어서 끼운다 (수직면만 위를 바라보게해서...
Topics: stl, speedrack, extension_cord, angle, thingiverse, Gadgets
5
5.0
Apr 8, 2021
04/21
by
Tony D. (Tony_D)
data
eye 5
favorite 0
comment 0
This is similar to my first Cord Cobra model except this one is specifically for those conventional flat power cords you find on most things around your house. The Cord Cobra Wrapper uses a single piece of 550 cord and two printed pieces. Start with a piece of 550 cord around 2 feet long then cut it down to the length you need once you determine which cord you're going to use it with. The Cord Cobra Wrapper can be easily wrapped around the end of the cord when not in use. This way it stays with...
Topics: extension_cord, cord, Household, stl, thingiverse, cable
4
4.0
Apr 27, 2021
04/21
by
Paul Tsigakis (paultsigakis)
data
eye 4
favorite 0
comment 0
A bracket for hanging up a multi-way extension cord from Biltema https://www.biltema.no/bygg/elektro/grenkontakter/grenkontakt-jordet/grenkontakt-med-bryter-2000038281 Art.nr. 46-3494
Topics: extension_cord_holder, thingiverse, Biltema, stl, Organization
1
1.0
Apr 20, 2022
04/22
by
Rich St. Onge (3DCDN)
data
eye 1
favorite 0
comment 0
This is used to cover an extension cord connector which I had to replace due to shorting.
Topics: thingiverse, Automotive, extension_cord, Block Heater, stl
0
0.0
Aug 15, 2022
08/22
by
Archangel Greshnik (Greshnik)
data
eye 0
favorite 0
comment 0
За основу взял катушку из под пластика разборную. Купил розетку и трубку алюминиевую. Шпилька для стягивания была 6мм. В трубку насыпается соль в притык, закупоривается, нагревается на плите или горелкой и гнется. Аккуратно не обожгитесь, алюминь хорошо греется. Ручка и...
Topics: electric, extension_cord, stl, thingiverse, DIY, extension
3
3.0
May 20, 2021
05/21
by
Jurassic73 (jurassic73)
data
eye 3
favorite 0
comment 0
I needed some clips to hold my extension cord on the back of our front porch pillar. These work well for a single extension cord. Print as is with stl file with piece standing on end. Cylinder opening is 8mm in diameter. The cable being straight will keep it in place. Mounted with this 3M adhesive tape: https://www.amazon.com/Scotch-Mounting-0-75-inch-350-inches-110-LongDC/dp/B009NP1OBC/
Topics: Organization, thingiverse, extension_cord, stl, cable_clip
2
2.0
Oct 29, 2021
10/21
by
Ando Roots (sqrooted)
data
eye 2
favorite 0
comment 0
2 mounting brackets for a simple extension cord. Enable to fix the cord to a wall with screws. Fits rectangular cord with dimensions 40x55mm. Sample: https://www.k-rauta.ee/p/pikendusjuhe-hama-power-strip-black-1-4m/a5zr?cat=a0h&index=24
Topics: extension_cord, thingiverse, stl, cable_management, Organization
10
10.0
Apr 5, 2021
04/21
by
Per Malmqvist (MrStarhouse)
data
eye 10
favorite 0
comment 0
Holder for European style extension cord outlets. Should fit many common types, maybe not UK versions though.
Topics: thingiverse, Extension_cord, Household, outlet, stl, holder
2
2.0
Nov 30, 2021
11/21
by
Parand Akbari (parandakbari)
data
eye 2
favorite 0
comment 0
We have designed this component to protect electrical connections. It snaps around the point where two cords come together. This also eliminates shorting out and the chore of reconnecting cords that have been accidentally pulled apart. One of the challenges that market extension cord covers faces is that they do not fit all sizes of extension cords securely, so creating an extension cord cover with 3d printing gives us this opportunity to produce them in low volume with different sizes without...
Topics: thingiverse, stl, #extension_cord_cover, 3D Printing
10
10.0
Apr 5, 2021
04/21
by
Patrick Forringer (destos)
data
eye 10
favorite 0
comment 0
Built this pulley for the fab lab, as the extension cord drops weren't exactly where I wanted them… It has 2 DOF so forces affecting on the main truss aren't great enough to snap the 3D printed parts. ###Supports cables up to slightly larger than half and inch. There is one large printable bearing ```print-_head.stl``` that would be best to print in another plastic to prevent wear between the parts. ( I may try to merge those two interfacing parts into one part with a ball bearing design, in...
Topics: thingiverse, pulley, roller, fablabtulsa, stl, Parts, extension_cord
3
3.0
Jan 5, 2021
01/21
by
Ralph (x12a1f)
data
eye 3
favorite 0
comment 0
Simple holder for power strips. The included STL file is for power strips measuring 55x42 mm. For other size powerstrips you can use the OpenSCAD file. See [power strip holder](https://github.com/x12a1f/rol/blob/master/doc/powerstripholder.md) on github for more information on how to use and customize the holders.
Topics: cable_management, outlet, Organization, stl, extension_cord, thingiverse
3
3.0
Jan 11, 2021
01/21
by
Steven Allmon (COMSECFOR)
data
eye 3
favorite 0
comment 0
These are brackets designed for the 15' extension cord power strip from Harbor Freight model #62437. Simply cut off the old brackets that suck with some snips. Print these out and use the provided screws. Mount.
Topics: thingiverse, stl, extension_cord, mounting_bracket, Parts, bracket
10
10.0
Jan 11, 2021
01/21
by
(jbukont)
data
eye 10
favorite 0
comment 0
I needed to run a 100ft 12 gauge extension cord across my workshop, but legally can't have it run on the ground where it can be tripped over. This allows you to hang the extension cord from a standard drop ceiling. I added a large cable hook area to accommodate the 11mm diameter 12 gauge extension cord I was going to use. *************Update 4/19/17 ************** OK, so the original verions that I remixed from the source file wasn't very good. It would grip a drop ceiling frame, but wouldn't...
Topics: thingiverse, stl, extension_cord, Ceiling, Parts, ceiling_hook
9
9.0
Jan 15, 2021
01/21
by
David Donald (wrxsti15)
data
eye 9
favorite 0
comment 0
Alienware Dell Laptop Charger and extension cord holder/mount Mounted on side of Ikea sliding table in bedroom to keep cable organised. WW4XY GENUINE Dell Precision M4600 M4700 M6600 M6800 180W AC Power Adapter
Topics: thingiverse, stl, extension_cord, holder, Computer, laptop_charger
5
5.0
Mar 5, 2021
03/21
by
Joe Bauer (Ohiojoe)
data
eye 5
favorite 0
comment 0
Wife wanted an extension cord from wall outlet to bidet. Of course she wanted it to look nice and neat! I printed two types of cord clips, the wider one is attached under the bathroom cabinet. The narrower one is the wall attachment. Printed in PETG, because that was what was in the printer at the time. Two STL files. 7mm and 8mm cord size. The length was made to fit Gorilla Glue Double Back tape width. I used Tinkercad, very simple.
Topics: stl, cable_clip, extension_cord, Organization, clip, thingiverse
4
4.0
Apr 13, 2021
04/21
by
MacGyver (MacGyver)
data
eye 4
favorite 0
comment 0
I needed a way to hold my new extension cord in place so I created this thing.
Topics: thingiverse, household, clip, wire, stl, Organization, extension_cord
3
3.0
Jan 19, 2022
01/22
by
Chris N.G. (theoptimist)
data
eye 3
favorite 0
comment 0
Wifi Smart power strip desk bracket.
Topics: thingiverse, extension_cord, strip, Office, stl, power, smart
0
0.0
Aug 14, 2022
08/22
by
Sergey Mashchenko (pulsar123)
data
eye 0
favorite 0
comment 0
This is a fully parametric model (in Autodesk Fusion 360) for a hook to support a power extension cord - mostly for outdoor applications (e.g. to thread an extension cord along your fence, or wall). Designed for standard drywall screws, can be adapted for any other countersink screws. You'll need to print a bunch of these for a typical scenario. Important parameters: - wire_diam : the electric cord diameter. Should be slightly larger than the actual diameter, to make sure the cord can be...
Topics: outdoor, extension_cord, stl, thingiverse, hook, Outdoor & Garden
5
5.0
Apr 8, 2021
04/21
by
Tony D. (Tony_D)
data
eye 5
favorite 0
comment 0
The Cord Cobra is a heavy duty extension cord tie that stays with your cord whether the cord is in use or hanging up. It simply uses (1) one foot piece of 550 Cord and (2) 3D printed pieces. When your cord is being used, simply wrap the Cord Cobra around the end and clip it on. I'm currently working on a version for the traditional flat power cord for items around your house.
Topics: cord_management, extension_cord, cord, Household, stl, thingiverse
3
3.0
Apr 24, 2021
04/21
by
David Mikulik (dmikulik)
data
eye 3
favorite 0
comment 0
The holder for thePowercube extension cord
Topics: stl, extension_cord, holder, Household Supplies, thingiverse, PowerCube
3
3.0
Jan 5, 2021
01/21
by
(imnorm)
data
eye 3
favorite 0
comment 0
I designed this to use for wrapping a cord attached to a heavy duty outlet strip I use in a mobile tool cabinet. The idea was that I wanted something that could handle a heavy gauge extension cord and that I could use two of these to tightly wrap any excess cord when the mobile unit is in its regular location.
Topics: stl, wrap, extension_cord, thingiverse, cord, hook, extension, DIY
10
10.0
Jan 14, 2021
01/21
by
Jacob Denney (Jacoza)
data
eye 10
favorite 0
comment 0
This is a simple cord folder/clip for extension cords or computer cables. I use this in my garage to hold and organize my printer cord and extension cords. Very basic design and easy print, holds well onto any 2 x (2,4,6,8) board.
Topics: wire, thingiverse, stl, extension_cord, 2x4, organizer, cord, Organization
4
4.0
Apr 1, 2021
04/21
by
Joe LaMotte (joe9216)
data
eye 4
favorite 0
comment 0
I designed a cord organizer wall hanger. it is split into a few sections that have different thicknesses. you can connect them without the spacer, with the 5mm spacer or with the 10mm spacer and corresponding keys depending on your cord thickness and length. These work great when paired up and the cord wrapped between the two. Included is the SKP for sketchup if you'd like to make changes.
Topics: wrap, cord, extension_cord, thingiverse, organizer, Organization, stl, hanger
6
6.0
Mar 17, 2021
03/21
by
shaun saggers (ssaggers)
data
eye 6
favorite 0
comment 0
Upgraded version of a hook that I did previously (for hanging a longboard), to suit use in my garage, specifically for hanging extension cords. 20mm wide. 45mm hook depth. see sketch in images for other dimensions. Beefed up to 4mm thick - I recommend using ~5 perimeters (depending on perimeter width), so that the entire print is perimeters with minimal infill), for strength Two screw holes (only need to use the top one, but use the second hole as well if you're hanging a heavy weight from the...
Topics: extension lead, garage, hook, extension_cord, stl, thingiverse, Organization
5
5.0
Apr 20, 2021
04/21
by
Mathias Korsbakke (FarmerThias)
data
eye 5
favorite 0
comment 0
I made this extension cord holder because i couldn´t find one i liked. So 20 minuts later in fusion 360 this is the result. The holes are 6mm and it fits if you use 5mm screw/bolts to mount it. No Support needed, but don´t go over .2 in layer height.
Topics: thingiverse, stl, Tool Holders & Boxes, garden_hose, extension_cord
3
3.0
Jun 11, 2021
06/21
by
Eugene Sedov (SEA17)
data
eye 3
favorite 0
comment 0
I remixed the inner wedge parts to fit reel with 2.5 inch (eSun, MG Chemicals and so on). Use the wire clips from source thing. Thanks to Tekcor17 he placed the Fusion 360 files in his remix https://www.thingiverse.com/thing:4811071 I used an inner hole and redone the surrounding surfaces
Topics: spool, reel, Household, filament, thingiverse, wedge, extension_cord, stl
2
2.0
Dec 14, 2021
12/21
by
tony wright (tony8888)
data
eye 2
favorite 0
comment 0
This is not really a remix as I made it from scratch but was inspired by the "Wago 221 Power-Rail" by _hedwig_. This is to fit the cheap Chinese Wago "knock off" versions available from Aliexpress. it is just a 3 way one only as that is what I needed. I have also added a cable tie from below. (It needs to be quite a fine cable tie but it fits the ones I had.
Topics: Extension, stl, thingiverse, extension_cord, Electronics, Non-Wago, Wago
3
3.0
Jan 19, 2022
01/22
by
(matthijsbos)
data
eye 3
favorite 0
comment 0
Replacement end cap for desktop extension socket that holds additional keystones for eg. ethernet. Has a recess for 8mm silicone anti-slip feet on the bottom. Premium-Office-Line extension socket such as: https://www.brennenstuhl.com/en-DE/products/extension-leads/premium-office-line-extension-socket-6-way-black-light-grey-3m-h05vv-f-3g1-5 Onshape document:...
Topics: power_cord_mount, keystone, thingiverse, extension_cord, Office, stl
4
4.0
Mar 22, 2021
03/21
by
Jakub Gocyk @ Allprint (JGFTW)
data
eye 4
favorite 0
comment 0
Power strip EPS-503W-2 250v 10a mount. As you can see the power strip itself is not that standard-shaped, but i have managed to design and create a mount for it = 3DPRINTING RULEZ!!!!111
Topics: stl, organization, Power_Strip_Mount, extension_cord, Organization, thingiverse
3
3.0
Oct 15, 2021
10/21
by
james weeks (turboprint3D)
data
eye 3
favorite 0
comment 0
just a little clamp for holding an extension cord up
Topics: thingiverse, stl, extension_cord_holder, DIY, extension_cable_clamp
3
3.0
Jan 6, 2021
01/21
by
Andrew Wagner (farsidethingiverse)
data
eye 3
favorite 0
comment 0
This is a cover for where the end of an extension cord meets the device chord being plugged in.
Topics: cover, outdoor, stl, extension_cord, Outdoor & Garden, thingiverse, plug
6
6.0
Jan 21, 2021
01/21
by
Alejandro Aguilera (Fenixer)
data
eye 6
favorite 0
comment 0
This is a sturdy hook that will be able to hold a big weight. I'm using it to hang different things: hoses (15m and 25m), a very very heavy (around 15kg) extension cord, a 13.3kg ladder and more stuff! Two versions are provided: wall mount and shelves mount (for M6 screw and nut). Right now the wall mounted version holds water hoses and it's been doing so for a year with frequent use. The second version it's a remix for a type of specific shelves and is holding a very long extension cord...
Topics: extension_cord_holder, Created_with_FreeCAD, hook, hose, water_hose_hook, Wall_Hanger, wall_hook,...
7
7.0
May 1, 2021
05/21
by
Sergey Mokhov (smokhov)
data
eye 7
favorite 0
comment 0
**Assembly Instructions** 1. Cut a 1 1/2 inch wide hole in the spool where filament used to be wound. 2. Thread extension cord through that hole into the side hole of the spool. 3. Wedge outlet side of the extension between the 2 parts and push them inside of the filament spool hole. 4. Mount wire clip into smaller holes. **Printing Tips** - Print wire clip vertically so cantilever clips are strong. - Preferrably use tree supoprts. - I had to adjust "X/Y support distance" to 0.3 so...
Topics: stl, Overture, filament_spool, Organization, extension_cord, spool, thingiverse
3
3.0
Mar 10, 2021
03/21
by
Mario Soliz (WristyArtifact2)
data
eye 3
favorite 0
comment 0
Designed for the purpose of supporting a 25ft cable. I'm sure it could support more. It was installed inside my workshop for a movable table.
Topics: Tool Holders & Boxes, cord, stl, thingiverse, extension_cord, holder
4
4.0
Jan 4, 2021
01/21
by
Giovanni Esposito (Giovanni73)
data
eye 4
favorite 0
comment 0
Kit to re-use a old filament spool as a electric extension cord The included version is for 52 mm hole spool and 11x35 mm electric female plug For different dimensions just ask... Kit per riutilizzare una vecchia bobina di filamento trsformandola in una prolunga La versione inclusa è per bobine con foro da 52 mm e presa da 11x35 mm Per altre misure basta chiedere... Se vi piace e volete offrirmi un caffè ... https://www.paypal.me/giovanni3d If you like it and want to offer me a coffee ......
Topics: reuse_spool, stl, extension_cord, Creative_recycling, recycle, thingiverse, DIY
