0
0.0
Apr 20, 2022
04/22
Apr 20, 2022
by
Jeremias Wittmann (PrusaJorek)
data
eye 0
favorite 0
comment 0
This mount is designed for Amazon Basic USB 3.0 Cable (3m) You only need two of these cables. Printed with a Prusa Mini+
Topics: thingiverse, usbmount, usb, 3D Printer Accessories, USB_Holder, stl, underdesk
1
1.0
Apr 20, 2022
04/22
Apr 20, 2022
by
Justin Masse (Webtron18)
data
eye 1
favorite 0
comment 0
I really like GoToTheWall's original, but I wanted it to fit flush with the desk so I removed the handle and added a small hole in the front. Original: https://www.thingiverse.com/thing:4667782
Topics: thingiverse, drawer, Underdesk_drawer, desk, Organization, stl, desk_drawer
1
1.0
Apr 19, 2022
04/22
Apr 19, 2022
by
jose guevara (tetonsio)
data
eye 1
favorite 0
comment 0
Print vertical with the end on bed. No need for supports.
Topics: Audio, under_desk_mount, thingiverse, focusrite, underdesk, support, first_gen, under_desk,...
0
0.0
Apr 19, 2022
04/22
Apr 19, 2022
by
Adnan Nash (adnanklink)
data
eye 0
favorite 0
comment 0
Simple headphone holder to screw into your desk. Holes are ANSI#8 sized though you want smaller screws so that you arent threading into the mount.
Topics: thingiverse, headphone_hanger, 3D Printing, screws, stl, underdesk, headphones
0
0.0
Apr 19, 2022
04/22
Apr 19, 2022
by
Justin Gutzman (jgutz20)
data
eye 0
favorite 0
comment 0
I wanted to mount my MSI Pro DP20Z 5M computer underneath my desk. Its official dimensions are 85 x 160.55 x 193.3 mm but the only one that matters in the height 85mm/8.5cm which is essentially 3.5" (3.34646), This one does have about 1cm of clearance at the top, so overall you have 95mm clearance. Print a couple of these and you can mount anything underneath your desk. I've also attached a picture of a couple versions along the way that i used to test. First one with all straight edges,...
Topics: under_desk_mount, thingiverse, desk_mount, Hook, pc_holder, MSI, under_desk, under_mount, Other,...
2
2.0
Jan 19, 2022
01/22
Jan 19, 2022
by
Adam Downes (z0mbiew0mbat)
data
eye 2
favorite 0
comment 0
Remix of the excellent drawers by chimeranzl; When I printed the first one of these I found occasionally I'd pull it a bit too far and it would come all the way out, this slide (v2 3M strip slide) and lock remix allows the drawer to be put onto the slide and then the locks clipped onto the frame to prevent the drawer from being pulled out accidently.
Topics: tray, desk drawer, small parts stoarge, under desk, thingiverse, household, Stoarge Gox, office...
3
3.0
Jan 19, 2022
01/22
Jan 19, 2022
by
DJ Mac (DJMac)
data
eye 3
favorite 0
comment 0
I spent some time trying to find a desktop cup holder that would free up my desktop space and avoid the risk of my beverages tipping over onto a keyboard, or worse. I didn't find any I liked, so I designed my own. Please note as part of your installation plans that the cup holder part inserts from behind, not from the front, to allow the stopper mechanism to exist, so you'll need to leave enough room for that. Design Notes: This design went through about 9 iterations before I came upon the...
Topics: Organization, thingiverse, sliding, underdesk, desktop cup holder, cup holder, stl
2
2.0
Jan 19, 2022
01/22
Jan 19, 2022
by
Argent Cove (argentcove)
data
eye 2
favorite 0
comment 0
This is a sheath for the metal mount of an under desk keyboard tray. FEL8017801 - Fellowes Designer Suites Compact Keyboard Tray https://www.amazon.com/gp/product/B00439564O/ 2 of these parts fit on the metal sides before sliding the tray in to it's track. They prevent metal-on-metal.
Topics: desk, under, thingiverse, underdesk, mount, keyboard, Office, stl, Keyboard_tray
2
2.0
Jan 18, 2022
01/22
Jan 18, 2022
by
Adrian Frühwirth (afkadri)
data
eye 2
favorite 0
comment 0
I optimized the Xbox controller underdesk holder. Now its very easy to put out the controller. The best way to print is that the holes where the controller sticks come in facing upwards because with this way you don't need support!
Topics: holder, Xbox_one_controller, optimized, thingiverse, underdesk, Video Games, controller, xbox,...
2
2.0
Jan 18, 2022
01/22
Jan 18, 2022
by
(VoidKiwi)
data
eye 2
favorite 0
comment 0
Modified the Design from antibimmer to work better for my needs. HOWEVER as cool and proud of myself as I am for this design. ONLY USE THIS DESIGN IF YOU WANT MINIMALISM. I say this because while uploading my remixed design I found a model which works for my needs a million times better than the one that I just printed. That design can be found below. Better design: https://www.thingiverse.com/thing:4835494
Topics: thingiverse, underdesk, Tool Holders & Boxes, soundblaster_g6, dac, stl
1
1.0
Jan 18, 2022
01/22
Jan 18, 2022
by
Kuba Kalisz (Kal1x)
data
eye 1
favorite 0
comment 0
Simple under desk hanger for Laptop power supply. In this case Asus ROG Strix G. It can hold any power supply that would meet below dimensions: Wide: 77mm Tall: 33mm
Topics: power_supply, Computer, thingiverse, hanger, underdesk, laptop, laptop_accessories, stl
1
1.0
Jan 18, 2022
01/22
Jan 18, 2022
by
Chris DeWolf (Ferfed)
data
eye 1
favorite 0
comment 0
USB mount for a few USB extension cables. made for these: https://www.amazon.com/gp/product/B073F84X43
Topics: usb_cable, thingiverse, underdesk, usb, mount, Office, Desk_organizer, stl, desk
1
1.0
Jan 18, 2022
01/22
Jan 18, 2022
by
Simon Love (enly1)
data
eye 1
favorite 0
comment 0
After trying out lots of under desk cable management options, I always ended up with issues with tangled cables and the need to re-arrange them when adding or removing stuff under my desk. So, I decided to design my own and think it fixes the issues I generally had with other under desk cable management solutions. 1. When open, there is nothing to get in the way of removing a bundle of cables. 1. Cables are held securely when clipped in. 1. Super easy to print 1. Make a lovely reassuring click...
Topics: thingiverse, underdesk, mount, Office, cable_holder, Desk_organizer, stl, cable, cable_management,...
1
1.0
Jan 18, 2022
01/22
Jan 18, 2022
by
(popatachi)
data
eye 1
favorite 0
comment 0
This is an underdesk mount for a Ugreen 4-1 card reader. I only use the micro and SD card slots, so didn't design an opening for the other side. https://www.ugreen.com/products/4-in-1-usb-3-0-sd-tf-card-reader
Topics: ugreen, thingiverse, underdesk, mount, Other, stl
1
1.0
Jan 18, 2022
01/22
Jan 18, 2022
by
Kerrick Jones (KromaDigitalArts)
data
eye 1
favorite 0
comment 0
Just a basic clip I made to add shelves to my desk, I originally made it to use a 3d printed shelf but seemed a wasted of material and time when I have tons of old card board boxes :) Turned out great for old boxes and the clip was designed to fit a 3/4 inch or 15mm desk with a little bit of room (4mm about) to slip the box between. I will now definitely be making more of these little guys as they have just increased my storage space a TON without sacrificing valuable real-estate on top of my...
Topics: shelf, easy_print, thingiverse, underdesk, 3D Printing, stl, storage, clip
1
1.0
Dec 14, 2021
12/21
Dec 14, 2021
by
(Iron_Harrier)
data
eye 1
favorite 0
comment 0
A simple mount to hold AC adapters since they don't fit in server rack cable organizers. I designed to be screwed into the bottom of a desk. Should fit a variety of adapters.
Topics: cable_management, Organization, stl, thingiverse, cablemanagement, AC_adapter, underdesk
1
1.0
Nov 30, 2021
11/21
Nov 30, 2021
by
Bülent Uğur (ugurbu)
data
eye 1
favorite 0
comment 0
I designed spool hanger and cover in Tinkercad and used customizer file to get my drawers for my empty spool drawer (Porima). Thanks to customizer file! You need also need 4 quantity of about 9-10 cm bolt and nuts to fix drawers to spool. You need to open holes on spool (180 degree) to 2 screws (about 2cm screws) the spool holder and cover parts together to prevent drop down under the table. 1. fix the hanger under the table first. 2.prepare drawers and fix on spool (not forget the holes before...
Topics: spool, Underdesk_drawer, thingiverse, spool_drawer, filament_spool, stl, Underdesk_spinning,...
1
1.0
Nov 8, 2021
11/21
Nov 8, 2021
by
Andreas Giesert (Andreas-Giesert)
data
eye 1
favorite 0
comment 0
Here it is: my design of an underdesk headphone hook: - only 2 parts and easy to print - very sturdy because all layers lay in the force directions - assembly without glue (I recommend assembling after screwing the hook to the desk) - mounting with 2 screws (50 mm apart)
Topics: under desk, Microphone, headphones_hook, headset_hook, under-desk, headphones, Headset_Hanger,...
1
1.0
Nov 8, 2021
11/21
Nov 8, 2021
by
Sebastian Pedersen (gullerboi)
data
eye 1
favorite 0
comment 0
LED clamp for mounting under your table. It is simple and easy to print and install. Mine printed in 5-7 min per piece. I mounted it with an M3 Countersunk flathead screw, as i put a hole in for that. I uploaded the part file for Solidworks, if you want to edit the design!
Topics: stl, led_strip, desk_lamp, desk, Office, underdesk, Led_Holder, led_mount, LED_light, thingiverse,...
1
1.0
Oct 26, 2021
10/21
Oct 26, 2021
by
chimera NZL (chimeranzl)
data
eye 1
favorite 0
comment 0
SD Card holder addition for Under desk drawer. Module fits 1/4 of the drawer. Made to fit into drawer version 2, 3 or 4. Also recommended to use with a drawer handle, as part of the SD Card holder module covers up the front hole. Also print out a side panel from https://www.thingiverse.com/thing:4896633 If you like it, click Like! If you make it, post your Make! If you have a problem with it, post a Comment and I will try and fix it!
Topics: drawer, Micro_SD_Card_Holder, SD_Card_Holder, underdesk, drawers, Underdesk_drawer, sd_card, stl,...
1
1.0
Oct 26, 2021
10/21
Oct 26, 2021
by
Dmytro Strelnikov (dstrelnikov)
data
eye 1
favorite 0
comment 0
Simple underdesk mounting braces for Topping E30/L30. You will need to print 4 of `topping_mounting_side.stl` for mounting either E30 or L30, and you will need to print in addition 2 of `topping_mounting_middle.stl` if you are going to mount both E30 and L30 side-by-side.
Topics: organization, mount, mounting, stl, thingiverse, underdesk, Organization, audio
2
2.0
Oct 15, 2021
10/21
Oct 15, 2021
by
RipDaPip RipDaPip (RipDaPip)
data
eye 2
favorite 0
comment 0
.4 Layer Height 2 Wall Line Count ✔ Optimize Wall Printing Order 4 Top and Bottom Layers 20% Infill Grid Pattern 220° C Printing Temps Brim Set to Print under supports too *cura option* Support Brim width under supports 4mm(7Lines) Brim on print 8mm Added a support free design Enjoy :)
Topics: thingiverse, drop, underdesk, stl, Organization
2
2.0
Oct 15, 2021
10/21
Oct 15, 2021
by
matthew patane (white_puma)
data
eye 2
favorite 0
comment 0
Wall or underdesk mount for USB repeater I designed this for the U305A UNITEK 5M usb c repeater (https://www.ebay.com.au/itm/193804736342) It's possible that it will fit for other repeaters (as i believe its a pretty generic design), but to be sure i put the dimensions of the unitek system i made this for in the images. If yours is the same size it should fit. If you print it standing up it shouldn't need any supports.
Topics: thingiverse, usbc, usb, underdesk, stl, wall_mount, mount, Office, UNITEK
2
2.0
Oct 14, 2021
10/21
Oct 14, 2021
by
Erik Pellom (pellomen)
data
eye 2
favorite 0
comment 0
This is an under the desk cable wrap to keep those pesky cables from being under foot. This is my very first design, but I needed something to wrap up my XLR cables that go through a hole in the middle of my desk. I didn't want those loose cables just hanging around, waiting for someone to snag their foot on them, so I thought I would wrap them up. I personally used supports, but you may be able to get away with none. Since this is my first project, I would really appreciate any constructive...
Topics: thingiverse, podcasting, underdesk, stl, Organization, cord_wrap
2
2.0
Oct 14, 2021
10/21
Oct 14, 2021
by
(kaleun96)
data
eye 2
favorite 0
comment 0
Under-desk mount for a Schiit stack with Introprose connectors. Tested on a Schiit Modi 3+ and a Schiit Magni Heresy, unsure if other or older versions work. Very stable when assembled, virtually no side-to-side movement and if the correct rubber feet are used in the top of the mount to push against the Magni there is no up-or-down movement of the stack inside the mount. Important to note that this is made for the Schiit Stack with the [Introprose RCA...
Topics: thingiverse, desk, underdesk, stl, mount, schiit_stack, Audio, Schiit_Modi, schiit_magni, schiit
1
1.0
Sep 13, 2021
09/21
Sep 13, 2021
by
BRANDON BOWMAN (BRANDONMBOWMAN)
data
eye 1
favorite 0
comment 0
a little under desk drawer, print flat don't forget supports like I did!
Topics: stl, thingiverse, drawer, desk, Desk_organizer, Tool Holders & Boxes, underdesk
3
3.0
Aug 22, 2021
08/21
Aug 22, 2021
by
Carlo Barraco (TheGomba)
data
eye 3
favorite 0
comment 0
After several USB hubs, I finally found one that works the way I want it: the [TP-Link UH720](https://www.tp-link.com/ca/home-networking/computer-accessory/uh720/). I designed an under desk mount for the UH720 for better cable management under my new desk and decided to share it. The mount provides access to all the ports and the power button. Note that its a pretty snug fit, but will slide in if enough force is applied at the right angle. The mount is designed for countersunk M3 wood screws....
Topics: under_desk_mount, UH720, TP-Link_UH720, USB_hub_mount, USB_hub_holder, usb_hub, under_desk,...
1
1.0
Aug 22, 2021
08/21
Aug 22, 2021
by
reinalds mcdeindalds (ReinaldsMcDeinalds)
data
eye 1
favorite 0
comment 0
Small hook for cable management. For ikea linnmon/lagkapten table top or any width of 34mm. Should just slide nicely onto the desk. Use any material, doesn't really matter. Print with a brim if bed adhesion is a problem. Cable hole is 7mm, enough for ethernet cables, but anything thicker might be a problem.
Topics: cable_management, Organization, hook, stl, thingiverse, underdesk
1
1.0
Aug 8, 2021
08/21
Aug 8, 2021
by
Andrew Meyer (miremaker)
data
eye 1
favorite 0
comment 0
I remixed this bracket: https://www.thingiverse.com/thing:835356 I felt like the original works great for mounting on the side, but mine has to hang from under my desk. I wanted 2 holes for attachment (to prevent spinning). I also included the model with the single hole. If you are going into a wooden/composite desk, check the screw depth you might need first before touching a drill. I needed 3/4" screws for mine. I also beefed up the corners in a few areas to give it more strength on the...
Topics: desk_cable_tidy, tidy, underdesk, thingiverse, office_organization, desk_tidy, cable_tidy, office,...
1
1.0
Jul 25, 2021
07/21
Jul 25, 2021
by
Lukáš Purnoch (KiroTakeda)
data
eye 1
favorite 0
comment 0
Simple holder under table for this specific charger with two screws. With rightly tuned printer, it could be printed without supports.
Topics: thingiverse, charger, Organization, holder, cable, cable_holder, stl, underdesk, cable_management,...
3
3.0
Jul 22, 2021
07/21
Jul 22, 2021
by
Andrew Butcher (Butcher9_9)
data
eye 3
favorite 0
comment 0
A Simple Bracket to Mount a PS4 controller under a desk. Designed for a work colleague and I have not tested the Fitment yet, Will update as required. 3 Screw holes , 4mm hole. Fusion Files included for anyone that wants to modify it.
Topics: Video Games, gaming, stl, desk, controller, thingiverse, underdesk, mount
1
1.0
Jul 22, 2021
07/21
Jul 22, 2021
by
Olga Pavlova (olgapavlova)
data
eye 1
favorite 0
comment 0
Upside-down mount for another version of Ikea letter tray DOKUMENT (https://www.ikea.com/my/en/p/dokument-letter-tray-silver-colour-30160997/). Unfortunately, the original one (https://www.thingiverse.com/thing:2759384) does not suit.
Topics: Office, ikea, stl, mount, thingiverse, underdesk
3
3.0
Jul 22, 2021
07/21
Jul 22, 2021
by
AM 3DP (CorValidum)
data
eye 3
favorite 0
comment 0
I designed this to be able to have my Desk Lamp from Ikea under my, well, desk...
Topics: Office, holder, ikea, stl, desk_lamp, thingiverse, underdesk, ikea_harte
4
4.0
Jul 3, 2021
07/21
Jul 3, 2021
by
Daniel Andersen (DanAndersen)
data
eye 4
favorite 0
comment 0
Having a height-adjustable desk, I wanted to have my computer mounted under the desk. There is a relatively cheap pc tower under desk mount which are basically all the same Chinese manufactured holder. Often they are called "cpu holder" (why ever ...) Check out https://www.amazon.com/Under-Desk-Mount-Bracket-Wall-Mountable/dp/B01M4P7EXU for such a model. These holders can only hold cases up to 18 cm size. This extension allows tower cases to hold up to 26 cm wide tower cases, like my...
Topics: bequiet, case_mount, Computer_Accessories, STEP, Computer_mount, fusion360, holder, desk,...
2
2.0
Jun 21, 2021
06/21
Jun 21, 2021
by
remi zik (remizik)
data
eye 2
favorite 0
comment 0
a simple cable management thing to tape/glue/screw under your desk
Topics: desk, cable_management, Organization, thingiverse, hook, stl, underdesk, holder
2
2.0
Jun 20, 2021
06/21
Jun 20, 2021
by
Chris Brannan (Ultimatum)
data
eye 2
favorite 0
comment 0
This is a remote holder for the small remotes what come with pretty much all LED RGB strip lights. The print is pretty straight forward, just print on its back, most printers will handle the wall with ease. It might be stiff at first use, but if you mount it to under your desk with double sided tape, give it a few runs in and out then the PLA will flex create a smooth running fit.
Topics: remote_holder, thingiverse, Tool Holders & Boxes, Led_Holder, stl, underdesk, led_strip
2
2.0
Jun 12, 2021
06/21
Jun 12, 2021
by
Juan Vitali (juanvitali)
data
eye 2
favorite 0
comment 0
My desk has a step, so the back attachment is elevated. You can easily adjust the height. Printer: Ender 3 Slice settings: Layer Height: 0.28 mm Infill: 30% Supports: No (printed sideways - see the picture) Print Settings: 1 Left_tablet_holder 1 Right_tablet_holder Enjoy !
Topics: Tablet, underdesk, thingiverse, tablet_stand, tablet_holder, stl
5
5.0
Jun 11, 2021
06/21
Jun 11, 2021
by
(KaeVeeDesign)
data
eye 5
favorite 0
comment 0
Summary Keep your desk clear and your controller at the ready! My Under-Desk Xbox One Controller Holder stores your device in a practical yet aesthetically pleasing manner. I have also used this to store a Steam Controller to great success. I have used 3M command strips to hold this to the underside of my desk. I imagine any sufficiently strong double sided tape would also work. When printed as shown in the slicing picture there is no need for support material. I use 40% infill, finished weight...
Topics: Controller-Holder, Under-Desk, Mount, Desk, Under, Holder, Clutter, Controller, thingiverse, One,...
2
2.0
Jun 11, 2021
06/21
Jun 11, 2021
by
Martin Paiva (Stormtrooper1055)
data
eye 2
favorite 0
comment 0
This is just a very simple cable holder to put under your desk to organize yourself.
Topics: cable_clip, Tool Holders & Boxes, underdesk, cable_management, thingiverse, cable_holder, stl
2
2.0
Jun 11, 2021
06/21
Jun 11, 2021
by
James Demonchy (AstroJohn)
data
eye 2
favorite 0
comment 0
(O.o) Small practical storage to screw under the desk. Requires minimal support. No more messy office / workbench. Useful volume : Height 65 mm x Width 200 mm x Depth 250 mm you only need 6 screws and a little elbow grease Do you well;) ___________________________________________________________ Petit rangement pratique à visser sous le bureau. Nécessite un minimum de support. Fini le bureau/établi en bordel. Volume utile : hauteur 65 mm x largeur 200 mm x profondeur 250 mm Vous n'aurez...
Topics: Organization, underdesk, storage, thingiverse, bannette, tool_storage, Desk_organizer, stl
2
2.0
Jun 11, 2021
06/21
Jun 11, 2021
by
Michael Foster (FOSTRS)
data
eye 2
favorite 0
comment 0
This is a remake of https://www.thingiverse.com/thing:4082313 While I found it to be a great file and design my requirements needed some tweaking. I found the model to not have enough width or lower arm length for my 15"x9" laptop, so I extended both. The other key problem for me was the access hole on the lower arm was not big enough to accommodate a screwdriver. After I extended the lower arm I added another access hole and expanded both. I also smoothed all visible edges and added...
Topics: Organization, underdesk, stl, remix, thingiverse, laptop
2
2.0
Jun 11, 2021
06/21
Jun 11, 2021
by
Tom (boredomwontgetus)
data
eye 2
favorite 0
comment 0
A loose fit underdesk mount for the Steelseries Siberia 840 "Breakoutbox". For easier printing it is split in three parts. You need at least the top and bottom part. I added spacers as i had a hard time reaching the battery slot when it is mounted flush to the desk. I used 4x60mm screws for mounting.
Topics: siberia_840, headphones, steelseries, underdesk, Computer, thingiverse, headset, stl
2
2.0
Jun 10, 2021
06/21
Jun 10, 2021
by
Steve Ellingson (SEllingson)
data
eye 2
favorite 0
comment 0
Designed this bracket to mount a Anker 4-Port Ultra-Slim USB 3.0 Hub under my desk.
Topics: Anker, underdesk, thingiverse, DIY, stl
2
2.0
Jun 10, 2021
06/21
Jun 10, 2021
by
Steve Ellingson (SEllingson)
data
eye 2
favorite 0
comment 0
Designed this bracket to mount an Insignia USB Type-C Memory Card Reader under my desk, but still keep it accessible from the front and in place when pushing a card in.
Topics: underdesk, insignia, thingiverse, DIY, stl
2
2.0
Jun 10, 2021
06/21
Jun 10, 2021
by
Steve Ellingson (SEllingson)
data
eye 2
favorite 0
comment 0
Designed this bracket to hang my Presonus AudioBox iTwo under my desk.
Topics: underdesk, Presonus, thingiverse, DIY, stl
2
2.0
Jun 10, 2021
06/21
Jun 10, 2021
by
Christian Pixner (pixi2012)
data
eye 2
favorite 0
comment 0
Glashalter für Stielgläser. Vorne leicht angeschrägt damit sie auch nicht von alleine rausfallen können
Topics: Organization, glass, underbuild, underdesk, wandhalterung, unterbau, thingiverse, glas, wall_mount,...
1
1.0
Jun 10, 2021
06/21
Jun 10, 2021
by
Jesper Egsgaard Nielsen (Mowglli)
data
eye 1
favorite 0
comment 0
Size Size overall 18.0 x 20.5 x 6.0 cm (WxLxH) Desk outer 17.0 x 20.0 x 5.0 cm (WxLxH) Desk iner 16.5 x 19.5 x 4.8 cm (WxLxH) The holder is printed in PLA and the drawer is printet with ASA. I'll recommend printing both parts in PLA. Drawer facing with the buttom at the buildplate Holder with the backside at the buildplate, so standing tall. Holder took me 18 hours +/-, with a not so optimized 3D-printerprofile As you see i mounted it under my desk. The clearance at the top is there so all...
Topics: home, organizer, Retrogaming, Underdesk_drawer, Mounted, design, homework, drawers, underdesk,...
2
2.0
Jun 10, 2021
06/21
Jun 10, 2021
by
Olga Pavlova (olgapavlova)
data
eye 2
favorite 0
comment 0
Suits for Moleskine Large (13 cm x 21 cm). To mount: 6 screws 3 x 12 mm or 3,5 x 12 mm.
Topics: Organization, holder, underdesk, moleskine, thingiverse, Voronoi, stl
3
3.0
May 1, 2021
05/21
May 1, 2021
by
Niklas Meyer (zookee1)
data
eye 3
favorite 0
comment 0
This is a Under Desk Mount for the Fossil Sport **43mm**. **It is a tight fit so beware of scratches!** I am using a screen protector and have no problem with scratches of any sort due to it. Putting the watch in: https://youtu.be/eXJdjVCAP4o
Topics: stl, underdesk, charger, fossil_sport, fossil, thingiverse, Gadgets
5
5.0
May 1, 2021
05/21
May 1, 2021
by
Diego Bellagamba (diegobellagamba)
data
eye 5
favorite 0
comment 0
This is a round shape cable holder that can be fixed under your desk with only 1 screw. As shown in the photo, taking advantage of the elasticity of the material, the slot opens to let the cables pass, then closes by itself to prevent them from coming out. It can be printed in PLA or a similar material in elasticity, but it must be printed by placing the cylindrical section on the print bed, to prevent it from breaking during the use described above.
Topics: stl, cable_clip, cable_holder, underdesk, cable_guide, Desk_organizer, cable_management,...
