4
4.0
Jun 21, 2021
06/21
by
Aleksei Filimonov (filimonic)
data
eye 4
favorite 0
comment 0
Create a hole for mounting your model to a wall. Import it to your project, Scale (some 3D tools need scaling 0.1) Align and Cut out.
Topics: customizable, wall_mount, screw, thingiverse, Other, stl, openscad
10
10.0
Jan 18, 2021
01/21
by
Maker's End Info (makersendinfo)
data
eye 10
favorite 0
comment 0
1/2" ID Copper Pipe Wall Mount Flange; Three-screw. We stick standard 1/2" ID copper pipe/tubing up in a lot of places to hang spray bottles, pliers, cables, you name it. This is an over-built, over-designed wall-mount flange with significant support material on one section for underneath the pipe. The screw holes are for 0.135" screws (~#6) and the (flat) countersink is an additional 0.0625" (1/16"). That happened to fit a bunch of extra screws; we'll upload a version...
Topics: rod, thingiverse, Organization, wall_mount, flange, half_inch, stl, pipe_flange
4
4.0
Apr 13, 2021
04/21
by
Maarten Janssen (DhrBaksteen)
data
eye 4
favorite 0
comment 0
A wall mount for 15cm terracotta plant pots. Top of the pot hooks into the mount and can optionally be strapped tight by looping some rope around the pot and through the holes.
Topics: thingiverse, plant_pot, pot, Outdoor & Garden, wall_mount, holder, mount, stl
9
9.0
Jan 19, 2021
01/21
by
Nick Tank (tankalicious92)
data
eye 9
favorite 0
comment 0
I recently bought a 50W 2 channel bluetooth amplifier on Ebay. The amplifier came with a case that works great for protecting the board but not much else. The bracket I designed allows you mount the amp on the wall while still utilizing the original protective case. It mounts to the wall using regular drywall screws and if done correctly they will sit flush and the case will slide right into place. Keep in mind that you will need to remove 2 of the back screws from the case to allow it to slide...
Topics: Electronics, thingiverse, amplifier, wall_mount, stl
2
2.0
Nov 30, 2021
11/21
by
John Sutherland (John8)
data
eye 2
favorite 0
comment 0
This is a re-scaling of Caliper Holder to fit my 4" Busy Bee Tools, Caliper. I also made it 2mm thinner off the back to save on filament.
Topics: 4 inch, caliper, wall_mount, holder, thingiverse, 100mm, Tools, stl, hanger
6
6.0
Mar 17, 2021
03/21
by
(wittless)
data
eye 6
favorite 0
comment 0
Wall mount for maglite with C cell batteries.
Topics: maglite_holder, maglite, stl, thingiverse, Organization, wall_mount
3
3.0
Mar 20, 2021
03/21
by
Spencer Searle (SpencertSearle)
data
eye 3
favorite 0
comment 0
This is a mounting panel that holds 5 C14 sockets with industry standard holes for secure mounting, as well as 2 screw holes at each end for wall mounting. This was designed for my maker space, as i needed two of these panels, that allow me to use multiple UPS systems to backup all the printers.
Topics: mount, panel, maker space, Electronics, c14, thingiverse, wall_mount, stl
6
6.0
Mar 22, 2021
03/21
by
Dennis Gärtig (KenKoLegend)
data
eye 6
favorite 0
comment 0
Hola mates. You can now attach your C270 easy on the wall. 90° view on your print and you are able to turn the head up and down with no problem. Just click the end of the cam into the hole and you are ready to go! v2: Optimized for frontdoors, making thicker for stability v1: Not tested yet Use 2x - 4 x 16 woodscrews Use 1x - M3 screw with its nut Follow: https://www.instagram.com/printineers for more.
Topics: stl, Logitech_Webcam, 3D_Accessory, webcam_holder, C270_mount, thingiverse, wall_mounted,...
4
4.0
Apr 24, 2021
04/21
by
Sylvio Schelle (usersylvio)
data
eye 4
favorite 0
comment 0
Both brackets are the same. Just mirror one. Tanks to TimmyTopHat. https://www.thingiverse.com/thing:2597775
Topics: wall_mounted, c64, wall_mount, stl, Other, Commodore_C64, thingiverse
8
8.0
Apr 20, 2021
04/21
by
Tomasz Milcewicz (tomil1)
data
eye 8
favorite 0
comment 0
Some CCTV cameras has only two option for mount, that's why I design this wall mount, to move the camera a little away from the wall and lower it slightly. Wall mount created in software Moment of Invention 3.0. Size: 170 x 80 mm.
Topics: Household, thingiverse, stl, wall_mount, camera_mount, camera
4
4.0
Mar 22, 2021
03/21
by
Mats Haugerud (Matseslats)
data
eye 4
favorite 0
comment 0
##CD Frame This is a frame designed for hanging your CDs on the wall. It is designed for 125 x 142 x 10mm CDs (Standard) ##Materials needed: >150 x 130 x 4mm piece of glass >1x Outer frame (Print upside down) >1x Inner frame I recommend sanding and painting the frame for a better and more professional looking result I have printed the frame and checked that everything fits.
Topics: stl, wall_mount, frame, CD_frame, Compact_Disc, Decor, thingiverse
5
5.0
Mar 18, 2021
03/21
by
Conner Arnold (connerarnold95)
data
eye 5
favorite 0
comment 0
needed a wall mount for my chamberlain klik3u garage opener to mount in the house for the detached garage. attached with a command strip.
Topics: garage, Electronics, chamberlain, thingiverse, clicker, WALL MOUNT, garage_door_remote, stl
12
12
Mar 21, 2021
03/21
by
Curt (reichwec)
data
eye 12
favorite 0
comment 0
THIS IS A FLAG MOUNT FOR A WALL MOUNTED CLASSROOM FLAG. I HAVE INCLUDED THE INVENTOR FILE AS WELL AS THE STL FOR YOUR USE. PRINTS WITHOUT SUPPORT ON DEFAULT SETTINGS. I HAVE INCLUDED THE FILES WITHOUT FILLETS ON THE EDGES AS WELL.
Topics: FLAG, Parts, stl, wall_mounted, part, thing, mount, parts, wall_mount, FLAG_HOLDER, wall,...
8
8.0
Jun 20, 2021
06/21
by
Rick Tress (ricktress)
data
eye 8
favorite 0
comment 0
A visitor mentioned that they were looking for something like a CPAP Hose Clip to guide the hose near their bed, so I designed and tested this. The bore is 20mm, and the two parts go together with a paperclip bent through the hinges, and clipped short. For my standard hose I found it slide through smoothly with a tiny bit of clearance, so if you want it to be a tighter grip, try printing at 95% scale, or packing a bit of paper or tape into the bore. It can be mounted with a standard size 8...
Topics: hose, Organization, wall_mount, screw, thingiverse, stl, medical, clip, guide, stick, mount, CPAP
5
5.0
Mar 15, 2021
03/21
by
Ooklaboo (ooklaboo)
data
eye 5
favorite 0
comment 0
For less than $10 in wood and PLA, you can build a CPAP support stand that can retail for well over $100. These are the necessary pieces to assemble a stand and suspend the CPAP hose above a sleeper's head so it won't get tangled around their neck or pillow during the night. It requires printing the stand, two clips clips plus the top clip and obtaining 1/4 inch wood dowel or fiberglass rod etc. to make the 2 horizontal legs that go between the box spring and mattress and the vertical rod that...
Topics: CPAP tower, untangle CPAP, thingiverse, RESMED Air Mini, Tower, CPAP lift support, Other, CPAP hose...
4
4.0
Apr 24, 2021
04/21
by
Seb Roux (goldoseb)
data
eye 4
favorite 0
comment 0
voici un support de pile mural pour CR2032 , il peux tout aussi bien être fixé avec du scotch double face
Topics: CR2032_battery, mural, battery, CR2032, pile, Wall_Hanger, wall_mount, stl, battery_holder, holder,...
3
3.0
Apr 5, 2021
04/21
by
(ChrisHerman)
data
eye 3
favorite 0
comment 0
Wall mount for battery charger & cable tie
Topics: thingiverse, 3D Printer Accessories, charger, stl, battery, wall_mount, CTEK
5
5.0
May 1, 2021
05/21
by
(ChrisHerman)
data
eye 5
favorite 0
comment 0
CTEK XS 0.8 CHarger Wall Mount
Topics: stl, charger, wall_mount, Organization, thingiverse, CTEK
3
3.0
May 21, 2021
05/21
by
Per Pålsson (Per_P)
data
eye 3
favorite 0
comment 0
I wanted a wall bracket for my Ctek charger, so I designed one that has enough space for 2 extra cables so that I can charge my car wether it is outside or inside the garage. My charger is the TimeToGo, but I guess it will fit most Ctek-chargers. Print the front with text down. I used Cyano-glue to glue the holder together.
Topics: laddare, Ctek, Charger bracket, thingiverse, Automotive, Car battery charger, stl, wall_mount
4
4.0
Mar 22, 2021
03/21
by
Magnus Gröhn (lillmange)
data
eye 4
favorite 0
comment 0
A simple wall hanger for CTEK charger. print it upright for minimal support usage. I user 35% infill
Topics: CTEK, stl, Wall_Hanger, wall_mount, Automotive, Charger, thingiverse
8
8.0
Jan 15, 2021
01/21
by
Kenan Kajkus (skipper7801)
data
eye 8
favorite 0
comment 0
I made this to organize my long LAN-cables but it fits most cables
Topics: thingiverse, stl, wall_mount, Organization, wall_hook, cable_management, cable_holder, cabel, wall,...
8
8.0
Apr 8, 2021
04/21
by
Egar Almeida (squareoctopus)
data
eye 8
favorite 0
comment 0
This was designed as a way to keep things organized inside cabinets without wasting space. Print as many as you want and keep those things in order!
Topics: organizer, cabinet, wall_mount, Organization, container, stl, thingiverse, organization
4
4.0
Mar 15, 2021
03/21
by
Christian Pixner (pixi2012)
data
eye 4
favorite 0
comment 0
For holes in 10-20-30mm
Topics: picture_frame, Bilderrahmen, thingiverse, bild, cabinet, wall_mount, Gadgets, schrank, stl,...
13
13
Apr 16, 2021
04/21
by
Lucian Depold (luciandepold)
data
eye 13
favorite 0
comment 0
I wanted to store my transparent storage boxes vertically to save space and to have almost everthing in them in sight.That's want these mounts are for ! You will need some 4 screws with a diameter of around 3mm. Print the mounts upright, so the screws end up pressing the layers together rather then splitting them. Try to create a little friction between the box and the mounts, by getting the spacing between them right when you mount them.
Topics: Storage_Box, cupboard_mount, small_items, thingiverse, cabinet_mount, boxes, stl, item_box, Tool...
10
10.0
Jan 18, 2021
01/21
by
Björn Kremer (chaos523)
data
eye 10
favorite 0
comment 0
Cable - Wallmount - 8x with LabelField
Topics: label, LAN, Electronics, cable_management, cable_holder, thingiverse, wallmount, dymo, tag,...
9
9.0
Mar 12, 2021
03/21
by
Marc Hoffmann (b14ckyy)
data
eye 9
favorite 0
comment 0
This is a small Cable Channel Mount plate with Room for LED Strip. Made this one for Mounting Cable Channel below my TV and Keep room for LED Strip to back-illuminate the cable channel. Test print is green but recommend printing transparent. Fits to cable channel up to 20mm wide. Hole for screw and screwdriver inserted for easy mounting.
Topics: thingiverse, Decor, Cable_Channel, wall_mount, led_strip, stl, mount
9
9.0
Apr 22, 2021
04/21
by
Timo (titoBLN)
data
eye 9
favorite 0
comment 0
Cable channel set TypeA - customized on your room - plug them together. 1. Print the cover elements with spiral print mode or single-wall with no infill (spiral print with 0 or 1 bottomlayer) 2. Fit the cover elements together in the right order and check the route. 2. Cut or drill out the cable entries on side and holes for wall mounting backside 3. Plug the elements together and mount the system My settings: -0 or 1 bottom layer -spiral mode -0,4mm nozzle -0,2mm layer high
Topics: Cable_Channel, computer, projector, sound, thingiverse, wall_mount, stl, wall, cable, Channel,...
4
4.0
Mar 15, 2021
03/21
by
Monika Muth (MoetyZuma)
data
eye 4
favorite 0
comment 0
This is a tiny Wall Mount for a single Cable. If you print it in original size it fits only for Cables with a diameter of 3,5mm or less. The diameter of the Nail you need is 2mm or less. You also need a tiny hammer and a lot of tact for nailing.
Topics: Parts, thingiverse, cable_clip, Wall_Hanger, wire_holder, wall_mount, wire_management,...
4
4.0
Mar 15, 2021
03/21
by
Bilal Bahij (bilalbahij)
data
eye 4
favorite 0
comment 0
Cable Clip for Wall Mount
Topics: thingiverse, Desk_organizer, mount, Electronics, wall_mount, stl, cable_management
3
3.0
Aug 22, 2021
08/21
by
Markus Utke (markuscosinus)
data
eye 3
favorite 0
comment 0
Small clip for holding a cable against the wall. Will fit a 8mm diameter cable and a 1mm nail. Printing: Printed with 0.16 mm with the adaptive layer height from Cura. Took 10 min and less than a gram of filament.
Topics: nail, cable_management, cable_clip, wall_mount, cable, wire_holder, stl, thingiverse, Parts
4
4.0
Apr 1, 2021
04/21
by
Jacob Lee (JacobLee_1)
data
eye 4
favorite 0
comment 0
I designed this specifically to hold a large bundle of cables and allow easy re-routing. It features a through-hole to allow you to easily use a screwdriver to fix it to the wall and a flat surface at the back to brace itself to hold heavy bundles. I have about 6 heavy power cables sitting in mine (with the screw going into a stud, although it probably doesn't quite need the stud for that weight yet) and it handles the weight very well, with plenty more room for more cables.
Topics: mount, cable, wall_mount, cord, thingiverse, cable_management, Organization, stl
4
4.0
Mar 15, 2021
03/21
by
J-F Bouchard (monsieurglad)
data
eye 4
favorite 0
comment 0
As I was already playing with the model to make it solid: https://www.thingiverse.com/thing:4734279 I also created this for double sided tape. 2 versions available.
Topics: tape, thingiverse, cable_clip, wall_mount, cable_holder, stl, Organization, cable_management
5
5.0
Nov 8, 2021
11/21
by
Rimaz Rauf (mazzprintz)
data
eye 5
favorite 0
comment 0
This is a cable mount or holder, you can use it to hook cables on the wall.
Topics: stl, wire_management, cable_clip, cable_guide, wall_hook, wall_mount, cable_management,...
5
5.0
Apr 20, 2021
04/21
by
Richard Kagerer (rkagerer)
data
eye 5
favorite 0
comment 0
I love the remixed HTC Vive HMD Minimalist Wall Mount, but I wanted a place to hang the excess cable dangling down from my Vive. So I designed this accessory. It mounts directly on top of the original fixture, sharing the same fasteners. It even has small bosses that fit into the countersink holes to keep things snug to the wall. You can coil the cable around it a few times for a tidy look, or just do 1 loop like I do and let the rest hang down toward the floor (less loops helps avoid twisting...
Topics: thingiverse, vr_gaming, stl, accessory, wall_mount, hook, Tool Holders & Boxes, vr_headset,...
8
8.0
Apr 17, 2021
04/21
by
Jan B. (spocky)
data
eye 8
favorite 0
comment 0
Cable Organizer for mounting at your wall. Be aware to not overstress the braces. Have fun :) p.s.: My printer failed with the print on the photo. That's why it looks a bit different than the STL. Nevertheless it works fine. 2018-01-07 Update: Added Rev. 1: Reduced the amount of large gaps and increased the amount of the small gaps (more space for USB-like cables). I also increased the size of the fall off barrier.
Topics: usb, usb_cable, cable_holder, Electronics, audio_cable, thingiverse, stl, cable, HDMI,...
9
9.0
Jan 19, 2021
01/21
by
Justin Spanier (JustinSpanier)
data
eye 9
favorite 0
comment 0
This is a mounting bracket for the ARRIS SURFboard SBG6950AC2 16x4 DOCSIS 3.0 Cable Modem. I got mine from Amazon. I printed it with 4 shell layers, and 50% infill. You'll need some sort of drywall anchor if you're mounting it on sheetrock. https://youtu.be/vZJ94KaUajM
Topics: thingiverse, Gadgets, ARRIS, wall_mount, cable_modem, stl
3
3.0
Jun 11, 2021
06/21
by
Andre L (Tesla_Andre)
data
eye 3
favorite 0
comment 0
Hello all, thats my Cable Mount Type 2 for my Wallbox. The Cable Mount has with a locking position. For release the Connector simply press the button.. BOM: - threaded pins M3x4 (2x) - 5er screws (3x) I would be happy if you support me-> https://ts.la/andre67927
Topics: Automotive, ev car, Tesla, thingiverse, wallbox, wall_mount, typ 2, stl
3
3.0
Jan 18, 2022
01/22
by
Rossi Force (rosforc)
data
eye 3
favorite 0
comment 0
Made to organize cables and as wall hooks. The key slots in the back are made for M3 screws.
Topics: Organization, thingiverse, wall_hook, cable_holder, stl, cable_management, wall_mount
3
3.0
Jun 12, 2021
06/21
by
Jacob Moore (MrGreaterThan)
data
eye 3
favorite 0
comment 0
This is a cable organizer and a shelf. It has lots of room for your cables and power adapters. You could also put it next to your bed to hold your cell phone while charging and it will hold your phone's charging cable when not in use to keep it off the ground. It has two variations. One uses 3M Command Strips and the other uses Screws. Print Settings: 4 Walls 5 Top 5 Bottom 15 % infill
Topics: bedside_holder, organizer, phone_holder, cable_holder, charging_stand, USB_Holder, usb_cable,...
3
3.0
Jul 3, 2021
07/21
by
Dharam Raj (Dharam)
data
eye 3
favorite 0
comment 0
A cable organizer that can be mount to the wall.
Topics: wall_mount, cable_clip, cable_tidy, cable_guide, Household, cable_management, cable, thingiverse,...
4
4.0
May 1, 2021
05/21
by
Leslie Wong (FearLesOne)
data
eye 4
favorite 0
comment 0
A remixed cable retainer for durability and larger countersink screw hole. Retainer holds 5-6mm diameter cable firmly -- CAT 6 Ethernet cabling in my use case. A mounting screw is required. Maximum screw head is 10mm diameter with 3mm recessed depth and major diameter of 4mm. For durability do not change orientation of object for printing. For example, printing the retainer with wall-side down would be a mistake as hooks would be much weaker due to inherent laminate weakness between layers...
Topics: stl, wall_mount, cable_retainer, cable_organizer, thingiverse, Other
3
3.0
Jan 7, 2021
01/21
by
Clemens Schartmüller (Aeefire)
data
eye 3
favorite 0
comment 0
mount for fixing cable (ties) to furniture or walls with a single 2mm picture hanger nail. No special print settings needed - should print in only a few minutes per piece. Scale if bigger cable ties or nails / screws are used.
Topics: cabletie, Organization, stl, mount, thingiverse, wall_mount
5
5.0
Apr 1, 2021
04/21
by
Tyler Barnes (dtylerb)
data
eye 5
favorite 0
comment 0
Print sideways (current rotation) with no supports. These mounts are designed to mount cables, devices, etc to a wall using nylon cable ties. Screw the mount to the wall through the middle, pass the strap through the slots on both sides, and around whatever you are trying to mount. For larger items, use multiple mounts. I usually far prefer these over the ones that just stick on with double sided foam tape, as they stay put. The commercial mounts of a similar design are generally nylon, and...
Topics: cable, cabletie, cable_managment, Wire_ties, wire_tidy, wire, zip, bundle, anchor, Zip_Tie_Anchor,...
5
5.0
Mar 5, 2021
03/21
by
Siegmund Schreiber (SamWhiskey)
data
eye 5
favorite 0
comment 0
This is a cable fixation for general purpose cable management. I used it for the skirting board of my office to have a fixation for the network cables. Available variants: Screw type for general usage Snap-in + screw type for Kopp 399702004 100x60 mm cable duct (EAN: 4008224542951) Important parameters for printing Nozzle: 0.3 mm Support: Touching Buildplate only Wall Line Count: 1 (to enforce layer adhesion) Infill Density: 100% Build Plate Adhesion: Brim is recommended if adhesion is an issue...
Topics: wall_mount, stl, cable_clip, cable_holder, Construction Toys, cable_management, cable, thingiverse
3
3.0
Apr 5, 2021
04/21
by
(MegaSaturnv)
data
eye 3
favorite 0
comment 0
Cusomizable / parametric mount for screwing any size cable (e.g. coaxial, video - DP / HDMI / DVI / VGA, mains) to wood or a wall with any size screw. Also allows multiple prints via stacking.
Topics: thingiverse, customizable, customizer, customized, stl, cable_holder, parametric, DIY, cable_guide,...
6
6.0
Mar 2, 2021
03/21
by
Markus Karl Wackermann (spreed)
data
eye 6
favorite 0
comment 0
This is a Remix of the Original CableWallHolder, but with longer holding cylinders and actual holes for M3 screws Update 09.10.2018: Added two more versions, lite & standard Like my Designs? - Support me by buying me a coffee :)
Topics: cable_management, wall_mount, Organization, thingiverse, stl, cable, holder, wall
3
3.0
Oct 14, 2021
10/21
by
Aris Kalomenides (akalomen76)
data
eye 3
favorite 0
comment 0
I wanted an easy and fast way to secure a cable along a wall. Adjust X/Y/Z according to your needs. Print as many required, use the appropriate drill bit, drill the hole, put the cable and push into the hole.
Topics: thingiverse, stl, wall mount, cable fastener, DIY, cable clip
3
3.0
Oct 14, 2021
10/21
by
Aris Kalomenides (akalomen76)
data
eye 3
favorite 0
comment 0
I needed a simple and fast way to hold a cable along a wall. Adjust x/y/z to your needs and print as many required. Just drill, put the cable and push into the wall.
Topics: wall mount, thingiverse, stl, cable fastener, DIY, cable_management, cable clip
2
2.0
Sep 14, 2021
09/21
by
Krisztian Szabo (Hejzenberg)
data
eye 2
favorite 0
comment 0
A simple design to keep you cables secured and organized on the wall against children's pulling. This design is for 4mm wires, but there wil be more sizes soon. Great replacement for the disgusting IKEA version.
Topics: wall_mount, stl, secure, thingiverse, security, screw, wall, Organization, cable, cable_guide,...
3
3.0
Jun 11, 2021
06/21
by
Graeme Yeo (graemeyeo)
data
eye 3
favorite 0
comment 0
A hook designed to clip onto a "String Swing" guitar wall mount bracket. The hook can be used to hang a jack lead (or other accessories) behind the guitar neck.
Topics: cable_clip, guitar_wall_hanger, wire_management, wire_hook, Music, cable_management, Wall_Hanger,...
